Kollmorgen has launched its AKMA servo motor built specifically for durability, cleanability, and versatility. The motor employs a hardened anodized aluminum surface to offer machine designers a cost-effective hygienic option to stainless steel in medium to heavy washdown applications.The lightweight design of the AKMA motor makes it easy t...

Aaron

2023-08-15

332

1

0

1, motor encoder alarm(1) Fault causes① Wiring error;② Electromagnetic interference;③ encoder hardware damage caused by mechanical vibration;④ Pollution caused by the site environment;(2) Troubleshooting① Check the wiring and eliminate errors;② Check whether the shielding is in place, check whether the wiring is reasonable and solved, and increas...

Jen

2023-07-22

223

1

0

In order to meet the requirements of mechanical equipment for high precision and fast response, the servo motor should have a small moment of inertia and a large locked-rotor moment, and have as small a time constant and starting voltage as possible, and should also have a longer overload capacity. To meet the requirements of low speed and high tor...

John Trant

2023-07-22

161

1

0

From the point of view of concern, motor control (here refers to servo motors) is mainly concerned with controlling one or more parameters in the rotation, speed, and position of a single motor to reach a given value. The main focus of motion control is to coordinate multiple motors to complete the specified motion (synthetic trajectory, synthetic ...

Kevin

2023-07-20

307

1

0

Question 1: How to locate the servo motor of the lead screw Zhilian when it goes from point A to point B? How do I know the distance from point A to point B? What are the methods?I will locate the command DDRVA DXXX DXXX Y0 Y1. But I don't know the distance from point A to point B How do I know? ,Question 2: What images or functions should be made ...

Cyril

2023-05-18

358

1

0

I want to make a torque machine with the plc and servo motor, see others do is to use the integrated machine zg3-8 0yt-7, this can go communication? Or does it use pulses to control the torque?

Keegan

2023-04-24

225

1

0

We all know the three-ring, in which the current ring is regulated by the driver itself, we need to do the work is to adjust the outside speed ring and position ring, which is the classic PID controlWhen we carry out positioning control, the speed curve and displacement curve will be planned in advance, and then the PLC is sent to the servo driver ...

Marshall

2023-04-24

274

1

0

The closed-loop controlled frequency converter can achieve closed-loop position control in the stopped state through encoder detection, locking the servo motor shaft at a fixed angle. This function is called servo motor locking or zero servo function.

Keegan

2023-03-18

217

1

0

I have seen a device that controls the servo directly through the screen. It should be a special address register for communication. But I want to know how to do it, including parameter setting.

Payson

2023-03-15

231

1

0

Mitsubishi JE servo pulse control. The program logic has been verified to be correct. Now the position of the equipment is not allowed to exceed the range after about ten minutes of operation. The monitoring Mitsubishi motor command pulse accumulation has drifted up. Later, the filter has been added to improve it. After grounding 0V, the single ser...

Payson

2023-03-13

196

1

0

One equipment on the production line and one servo are transplanted to the normal position. It has been determined that there is no problem with the mechanism. It should be an interference problem. The servo is Panasonic servo motor. I don't know how to eliminate this problem?

Vasili

2023-03-13

269

1

0

In the process of equipment debugging, it was found that the servo motor could not reach the specified position. After troubleshooting, it was found that there was a problem with the IO line of the driver. It would be good if it was replaced. The servo motor uses position control, and the command pulse sent by PLC will be lost due to the poor conta...

Marshall

2023-03-10

366

1

0

The servo motor moves intermittently and equidistantly. Assuming that the distance of each movement is 50mm, the calculated pulse is with a decimal point, which will cause cumulative error. Is there any solution?

Nugent

2023-03-07

367

1

0

The servo motor is used with the reducer, such as the planetary reducer. The reducer has a reduction ratio. The servo motor outputs the specified speed. After the reducer decelerates and increases the torque, will the speed accuracy of the output shaft of the reducer be improved? Or does the reducer affect the speed accuracy of the servo motor? Is ...

Vasili

2023-03-04

339

1

0

The servo motor moves up and down, has an origin, and moves up and down in the process of returning to zero. Each time, the value of moving up and in place is periodic, pulse signal, what is the situation.

Patrick

2023-03-04

335

1

0