chanelink logo
CHANELINK
Ελληνικά

RDCutist 3.0

Κατηγορίες:
Ruida
526
23
Δείτε τη μετάφραση
2023-08-30 
There is support for ruida?
I am using rdcutist 3.02.20 beta.
I have the following problems:
- Frame speed is very slow, can't change it.
- If I connect parts and load them into RG6563FG. Cutting occurs with a visit (not always)
- Focus, axis A can only be controlled in external coordinates. 
- IMPORTANT: In layer, membrane mode - does not turn on the laser.
Can I get fixes?
C

    • Jimmy-He

      2023-08-30
      1.Frame speed set in Panel ->Menu ->Speed
2.Need a more detailed description of the issue, providing pictures or videos.
3.The control of the A-axis is not related to the selected coordinate system. But a reset operation must be performed first before the A-axis can be controlled. If there is no reset but A-axis focusing is selected, the processing will alarm.
4、The version number of the board needs to be provided to determine whether it supports this function.
      Δείτε τη μετάφραση
      Απάντηση

    • Pavel_TT

      2023-08-31
      number board
      Δείτε τη μετάφραση
      Απάντηση
      • Pavel_TT

        : laser does not turn on, the red dot is always on

    • Jimmy-He

      2023-08-31
      I need these version numbers as shown in the picture
      Δείτε τη μετάφραση
      Απάντηση
      • Pavel_TT

        : version numbers

      • Jimmy-He
        Απάντηση
        @Pavel_TT

        : Can you provide an email address so that I can send you an upgrade file for the board?

      • Pavel_TT

        : I sent you a message by email.

      • Άλλες 7 απαντήσεις

    • Pavel_TT

      2023-09-07
      i updated the firmware
In layer, membrane mode - does not turn on the laser:
https://youtu.be/LX-KigiaOXw
      Δείτε τη μετάφραση
      Απάντηση

    • ROD

      2023-09-22
      Hi , how can i open multiple rlc files into one sheet, when i try it deletes the one already there?
Rod
        Δείτε τη μετάφραση
        Απάντηση
        • Jimmy-He

          : The rlc file contains processing related parameters, so during design, only a single file is supported for opening. If necessary, you can first open the rlc file, then save the AI file, and then open multiple AI files.

        • ROD

          : Thank you for the answer, I have another question if you have time. In my layer parameters the max pressure is 10bar, I need to go higher for aluminium(14bar)but Im unable to change this setting, is there a defult setting somewhere? Regards

      • Pavel_TT

        2023-09-25
        - If I connect parts and load them into RG6563FG. Cutting occurs with a visit (not always)
        Δείτε τη μετάφραση
        Απάντηση

      • Pavel_TT

        2023-09-25
        foto 2
        Δείτε τη μετάφραση
        Απάντηση

      • Pavel_TT

        2023-09-25
        photo 3
        Δείτε τη μετάφραση
        Απάντηση
        • Cityslicker

          : Hello Pavel, did you get a solution to the laser problem not cutting after the firmware upgrade?

        • Cityslicker

          : Pavel, did you manage to sort the laser not cutting issue with RDCUTIST3.0?

      Σχετικές συστάσεις
      Συλλογή
      Αναφορά