Renishaw will present its latest radio transmission detection system at the EMO fair in Hannover, Germany (18-23 September 2023, Hall 6, Stand B32).The RMP24-micro is the smallest wireless machine tool probe on the market, with a diameter of just 24 mm and a length of just 31.4 mm. In addition to its miniature size, the RMP24-micro offers m...

Christian

2023-06-06

198

1

0

I have all my setting just as it shows on here for the fiber laser and when I send a job its mirrored, what else could it be?

Patrick

2023-06-06

266

1

0

Hello ,I’m having a problem with my laser, but I’m not entirely sure what’s going on.I set up zero pieces, adjusted the focus, and started cutting my file.When the piece was finished, I wanted to run another cutting pass because it was apparent that it didn’t fully cut through the 4mm plywood. Initially, I performed a frame...

jessie

2023-06-06

275

1

0

I happen to have a Lightburn install of V1.0.0.1 on my shop computer. My annual license upgrade ran out a few weeks back, and I do plan on re-upping, but I have a few other expenses that I need to clear first (possibly a new laser tube).Is there a ‘Docking’ equivalent in this early version? How to I align objects (2 rectangles) so they...

roy

2023-06-06

342

1

0

I’ve been using the demo version and am looking to purchase a full license, but within the family there are 3 PCs and a laptop we’d like to use LB to design on and have mini PC in the workshop that would be used for local laser control, connection and possibly correction of files prior to burning and act as the server for the laser.What...

Liam

2023-06-06

227

1

0

Hi Im looking to finish off my first cut with my Xtool D1 Pro 20W, I have changed all the lines to the correct for cutting both inner and outer cuts. The lightburn software setting for both inner and outer cuts is set to 7.9/100, I have it set to inches so I think that the cut is inches as well, is that to slow and is cutting always done at 100 per...

Jen

2023-06-06

306

1

0

I updated to V1.4 and the numbers in the height/width/% boxes only show the numbers to the right of the decimal point. can’t figure out how to fix this. please see attached screenshot. thanks

John Trant

2023-06-06

354

1

0

How do i revert back to flat or plane cutting on my boss laser LS1420 machine? Just finished using the rotary set up and it been difficult getting back to flat engraving mode despite all my efforts.I use lightburn and have no issues with the software

Robert Evans

2023-06-06

203

1

0

I tried clicking “fill” but didn’t see anything happen and I’m not sure that’s the solution. TIA

Henry

2023-06-06

396

1

0

LioniX International, a provider of integrated photonics and custom MEMS device solutions, has teamed up with an alliance partner in the REAP program to develop an ultra-narrow line-width tunable laser ona chip that addresses the narrow range of near-infrared light. It is described as having a line width of 22 kHz, a tuning range of 45 nm, an outpu...

Marshall

2023-06-05

247

1

0

High power Industrial Blue Light Lasers has announced that it has signed a joint technology agreement with GE Additive Manufacturing, a subsidiary of GE Aviation, to explore the speed, accuracy and commercial benefits of blu-ray laser-based metal 3D printing."As we continue to advance our proprietary blue laser technology, we further increase the...

Kevin

2023-06-05

182

1

0

Ireland's University of Galway is working with the Tyndall National Institute at University College Cork to create two-dimensional semiconductors for low-cost sensors.The €200,000 project "two-dimensional semiconductor Pulsed Laser Annealing for Nanoelectronics" aims to dramatically improve the scalability, functionality, performance a...

Aaron

2023-06-05

236

1

0

The need to reduce the size of semiconductors, coupled with the problem that heat generated at device hot spots cannot be dispersed efficiently, has a negative impact on the reliability and durability of modern devices. Existing thermal management techniques are not up to the task. The discovery of a new way to dissipate heat by using surface waves...

Abel

2023-06-05

307

1

0

I’m working on a guitar fretboard. Usually the fret dots go in the middle of the fret board, which is easy to figure out in lightburn. But for this particular board I want the fret dots to be dead center on the left half between the edge of the fretboard and the center line. And also dead center between the two frets. Any ideas?

Williams

2023-06-05

340

1

0

What is causing this?Grbl 1.1f [‘$’ for help][MSG:‘$H’|‘$X’ to unlock]$X[MSG:Caution: Unlocked]okWaiting for connection…ok[VER:1.1f.20180715:][OPT:VMZ,35,254]Target buffer size foundokHomingok<Idle|WPos:0.000,0.000,0.000|FS:0,0|WCO:0.000,0.000,0.000>okStarting streamALARM:2G-code motion target exceed...

Smith

2023-06-05

281

1

0