Italiano

The rare decay of the Higgs boson may point to physics beyond the standard model

143
2024-01-26 14:10:32
Vedi traduzione

Particle physicists have detected for the first time a new decay of the Higgs boson, revealing subtle differences predicted by the standard model and potentially pointing to new physics beyond it. The research results are published in the journal Physical Review Letters.

The theoretically predicted Higgs boson since the 1960s was finally discovered in the European CERN laboratory in 2012. As a quantum field, it permeates the entire space and other particles move through it, gaining mass through their interaction with the Higgs field, which can be roughly imagined as a resistance to their motion.
Many properties of the Higgs boson, including how it interacts with other particles and their associated fields, have been measured to be consistent with the predictions of the standard model.

However, an unexplored mode of Higgs decay is theoretically predicted, where Higgs bosons occasionally decay and produce photons, namely photoquanta and Z-bosons, which are uncharged particles that transmit weak forces with two W-bosons.

Scientists from the European Center for Nuclear Research ATLAS and CMS collaborated to search for this particular Z+photon Higgs decay using proton proton collision data obtained from Run 2 from 2015 to 2018. The Large Hadron Collider at the European Center for Nuclear Research is a high-energy particle accelerator located near Geneva, Switzerland. It circulates protons in opposite directions while causing collisions at specific detector points, occurring millions of times per second.

In this operation, the energy of the collision between two protons was 13 trillion electron volts, slightly lower than the current maximum value of the machine, which is 2.1 microjoules in more relevant units. This is approximately the kinetic energy of an ordinary mosquito, or a grain of salt, traveling one meter per second.

Theoretical predictions suggest that every 10000 decays, the Higgs boson should decay into the Z boson and photon, which is the rarest decay in the standard model. It first produces a pair of top quarks or a pair of W bosons, and then they decay into Z and photons themselves.

Atlas/CMS collaboration, with the work of over 9000 scientists, has discovered the "branching ratio", which is the decay fraction of 34 decays per 10000 cycles, plus or minus 11 decays per 10000 cycles -2.2 times the theoretical value.
The measured score is too large -3.4 standard deviations higher than the theoretical value, but this number is still too small to rule out statistical luck. However, the relatively large differences suggest the possibility of meaningful differences from theory, which may be due to the fact that new particles outside the standard model are mediators beyond top quarks and W bosons.

One possibility of physics that goes beyond the standard model is supersymmetry, which assumes a symmetric relationship between half spin particles and integer spins, with each known particle having a partner with a spin difference of half an integer.

Many theoretical physicists have long been advocates of supersymmetry because it can solve many of the challenges that plague the standard model, such as the huge difference between the strength of weak forces and gravity, or why the mass of the Higgs boson, about 125 gigahertertons per volt, is much smaller than the large unified energy scale of about 1016.

Source: Laser Net

Raccomandazioni correlate
  • Top management changes at Laser Photonics Corp., a US laser equipment manufacturer

    Recently, Laser Photonics Corp. (LPC), a Nasdaq listed equipment developer, announced that it has appointed John T. Armstrong as its new Executive Vice President. Before assuming his position at LPC, Armstrong served as Vice President of Astronics Test Systems, a subsidiary of Astronics Corporation, a global leader in advanced technology and products in critical mission areas such as aerospace a...

    2024-11-20
    Vedi traduzione
  • From Fiction to Reality: Laser Cutting Technology Has Entered the Shipbuilding Industry

    Laser cutting is a type of metal processing. In industry, there are three main cutting methods: mechanical cutting, thermal cutting, and a set of high-precision cutting methods. Laser technology belongs to the third category. The cutting in this method occurs due to the influence of the laser beam on the product. In fact, it is the molten metal produced by rapid pulse point melting and then blowin...

    2023-12-28
    Vedi traduzione
  • Artists transform paper into meticulous laser cutting designs

    In the past few years, paper artists have demonstrated the versatility of their common fiber materials. Some people manually cut or carve paper, while others combine traditional craftsmanship with digital design. Ibbini Studio is in this situation. Abu Dhabi artist Julia Ibni collaborated with computer scientist Stephen Noye to create sculptural paper works inspired by decorative patterns such as ...

    2024-01-23
    Vedi traduzione
  • Optimizing the phase focusing of laser accelerators

    With the help of on-chip accelerator technology, researchers at Stanford University are getting closer to manufacturing a miniature electron accelerator that can have various applications in industrial, medical, and physical research.Scientists have proven that silicon dielectric laser accelerators can now be used to accelerate and limit electrons, thereby producing concentrated high-energy electr...

    2024-02-29
    Vedi traduzione
  • Researchers have demonstrated a breakthrough boson sampling method using ultracold atoms in optical lattices

    JILA researcher, National Institute of Standards and Technology (NIST) physicist, physics professor Adam Kaufman and his team at the University of Colorado Boulder, as well as NIST collaborators, demonstrated a new method of cross laser beam lattice sampling using ultracold atoms for boson sampling in two-dimensional optics. This study, recently published in the journal Nature, marks a significant...

    2024-05-10
    Vedi traduzione