I have been engraving some stars for christmas, but after a while i encountered a problem… Whenever i want to start engraving, i get an error message“Transfer failed - Lightburn 1.4.03There was a problem sending data to the laser. The machine may be busy or paused.”Ive encountered this twice now, but on the first try i just switc...

Williams

2023-12-04

140

1

0

I have tried everything I imported an HEIF file and when I go to engrave it I get ni layers in your projecr to output, What do I need to do. I have tried all the recommenced options.

Abel

2023-12-04

133

1

0

I have been trying to make multiple passes to cut through the material however my circles do not line up.

Aaron

2023-12-04

129

1

0

How do I turn on laser beam at low power so I can set the laser on the spot where I want it to start cuting?

Marshall

2023-12-01

148

1

0

I upgrade my machine to use a more power laser a few months ago. In the past few days the power supply will begin flash and the machine will not function.I figure there is either a short with the 4 to 3 wire adapter or the laser is pulling too much power.Once I unplug the adapter to the laser the machine powers on. I assume if it was a power draw i...

Tory

2023-12-01

147

1

0

In order to swiftly heat the material to the vaporization temperature, evaporate it, and produce holes in it, laser cutting involves the employment of a high-power density laser beam. The material is cut to completion as the beam shifts it through the perforations, which continuously generate thin (like 0.1 mm) slices.The technologies involved in ...

David

2023-11-30

161

1

0

ich habe nun LightBurn umfassend getestet und würde es gern kaufen.Ist es möglich, eine Lizenz auf mehreren Geräten zu verwenden?Ich habe 2 Rechner und würde gern auf beiden Geräten mit der Software arbeiten. Natürlich nicht gleichzeitig, aber mal mit meinem Computer und unterwegs mit dem Notebook.Nun kenne ich das von...

Henry

2023-11-30

122

1

0

I’m trying to create a grid of short lines using perforation mode. I’ve staggered the lines since I don’t want them to touch. The vertical lines look on but the horizontal lines, which are parallel, are offset in the preview. I have no idea why. My alternative method will be to make a whole lot of short lines using the array tool....

Robert Evans

2023-11-30

141

0

0

Recently purchased an atomstack A10 to learn and play around with a Laser machine and I like the Lightburn software as well.I just want to ask about the license, it says it can be used on three machines. I only want to use two machines but I’m worried my setup may cause an issue with the licensesingI am in the UK and my ISP is plusnet and I...

Jen

2023-11-29

176

1

0

Okay, I’d like to resize these texts into same width or height. I tried to use the encircled tools. It does the job but does not apply the lock aspect ratio which makes most of the text condensed or wide. Anyone please help me.

Liam

2023-11-29

143

1

0

Perovskite solar cells are solar cells that use perovskite type organic metal halide semiconductors as absorbing materials. They belong to the third generation of solar cells and are also known as new concept solar cells.operational principlePerovskite solar cells are solar cells that use perovskite type organic metal halide semiconductors as abs...

Patrick

2023-11-28

119

1

0

Having an issue with slots. On a drawing with several slots, all 3mm, only a few actually appear to be editable.I’ve checked there are no extra nodes or rounded corners in the drawing. The drawing seems to be closed as I only see one green node. No errors are present in the dialog box.

Christian

2023-11-28

129

1

0

I was using the same speed and the same power, but then it slows down a lot, but i dont know the reason, what reason can it be?I was using my laser cut machine to cut the polywood in 3mm and with the suggested speed power and pass, but then the machine just no more able to cut it through as from the beginningfor my laser the suggested speed is 350,...

Nugent

2023-11-28

116

1

0

I intend to cut two lines to transform the two areas into one. When I do “trim line” the line n stays in one. Then it creates open part problems. Does anyone know a way to not have to see each zone to manually join these points that don’t stay together?

Vasili

2023-11-28

115

1

0

Although it may be used to cut a wide range of materials with accuracy and versatility, laser cutting has several risks that should be considered before using it regularly. Certain steps need to be taken to guarantee both safety and the best possible outcomes. General safety measures for maintaining laser cuttings include the following:1. Put on ...

Terrelle

2023-11-27

113

1

0