I have two copies of lightburn 1.4.00 on two computer. the older laptop this window has 3 buttons “set origin, clear origin and set finish position”. The copy of lightburn 1.4.00on my new computer does NOT have these buttons.

Robert Evans

2023-06-13

545

2

0

I haven’t used the 2s for a while, and in the interim the software has moved onmy last available upgrade is 1.2.04, but prior actual work had been done on 1.2.01, which was working finei updated to 1.2.04 because trying to use a file created on that version on my desktop machine threw a message suggesting it may not work properly on the old...

Henry

2023-06-13

406

1

0

I have a new machine a Atomstack S10 PRO, Laser is 10-11 Watts max and my problem is that when using Lightburn I have to usemultiple passes to burn through 1mm veneer yet without changing a thing I switch to Laser GRBL and at 100% it will burn through the veneer, I do not understand what if any I am doing wtong? Why is it that both programs are set...

David

2023-06-13

528

1

0

I finally got around to getting my camera set up on my atomstack x20 with y axis extention and the setup and calibration seemed to go smoothly but when I tried to calibrate the alignment it tries to center the test file and puts the overlay centered in the workspace. The Y axis shift won’t move it down far enough to be aligned. I can change t...

Tory

2023-06-13

365

1

0

Germany-based high performance laser manufacturer HuBNER Photonics has announced the launch of the higher power Cobolt JiveTM 561 nm laser model.With a continuous wave output power of up to 1W, the Cobolt JiveTM 561 nm laser is ideal for demanding applications in fluorescence microscopy, especially super-resolution microscopy (such as DNA-PAINT),...

Keegan

2023-06-13

387

1

0

Sivers Photonics, a leading supplier of optical fiber communications and III-V semiconductor photonics devices in the UK, said it is currently conducting a comprehensive evaluation to improve its operational capabilities to meet batch production targets of more than 1,000 wafers per week.Start the optoelectronic foundry expansion projectSi...

Marshall

2023-06-13

353

1

0

Trumpf has announced that it has developed an artificial intelligence (AI) application for lasers that can make manufacturing more efficient. For example, electric vehicle manufacturers can use it to produce more electric motors in less time and reduce rework and scrap rates."In the future, we want to use AI to take the entire system of lasers, o...

Aaron

2023-06-12

442

1

0

Laser cladding, as a surface strengthening technology with high precision forming and low damage control, can endow parts with higher surface properties. As a low-cost coating system, iron-based coating has been widely used in the field of surface strengthening of various mechanical parts. With the pursuit of high performance and long life of parts...

Abel

2023-06-12

495

1

0

I have a problem which is more an annoyance than anything else but wonder if there is a solution.Here I have the visual grid set to the default of 10 and the work area zoomed so the grid legend is clear to read.However if I were to change the zoom, e.g. to zoom into an object or, as in this case, simply click the ‘zoom to frame’ selecti...

Williams

2023-06-12

323

1

0

I own a Thunder Nova 63 Co2 130w laser. A consistent issue I am having is inconsistent results. I place a 1/4" piece of acrylic (material is flat and anchored using pins inserted into honeycomb in the bed, send the file via light burn, and I get a perfect cut. Speed/Power(%) 14/97. At this speed and power the laser usually burns clean through the a...

Smith

2023-06-12

354

1

0

I have an XTOOL laser and it smokes a lot when i am burning a phrase on a cutting board. it smokes my whole house out, it even set off the smoke detectors off a few times. I have it in one of the rooms in my house because it is hooked to my desktop. does anyone have any ideas for keeping the smoke down?

Miller

2023-06-12

474

1

0

I tend to model on the desktop then save files to my server and open in the shop on the laptop.My laptop/control cpu settings were read from my machine. They appear to be accurate as far as estimated time in the preview and the actual time.But when modeling on the desktop I can see it is nowhere near the actual time. (example: Desktop 1:23min &rarr...

Cyril

2023-06-12

524

1

0

Hello!After installing the extension kit, I luckily stumbled upon a post that I had to update my laser. I now just have installed the 20w upgrade and have been running samples. Do I need to make any changes in Lightburn to reflect this upgrade? Download or settings? I can hang, but I’m not a wiz when it comes to computer programs.Thank you!

Gilbert

2023-06-12

354

1

0

Does anyone know why I am getting these pits, or random holes in the image and around the edge of my image in the glass?Settings are: Xtool D1 20w, Speed 7500, power 75% Bi-directional pattern, Line interval 0.100 mm, lines per inch 254.0, number of passes 1.

Clarence

2023-06-12

565

1

0

My DELL Latitude will not connect to XTOOL D1 PROI am using the correct configuration file but LB cannot find the XTOOL.

Terrelle

2023-06-12

529

1

0