The maintenance of helical gear reducers is an important measure to ensure their long-term stable operation and extend their service life. The following are some basic points for maintenance and upkeep of helical gear reducers:Regular inspection: Regularly inspect the gearbox, including checking for any abnormal wear, cracks, or leaks on the appe...

AL.TAL

2024-07-22

112

0

0

1. Gear overloadGear overload is a common fault of transmission gears, usually caused by unreasonable mechanical structure design of the transmission device, harsh operating environment, and excessive workload. Gear overload can cause gear cracks, gear tooth surface damage, bearing overload and other faults, which can seriously affect production ef...

Robert Evans

2024-07-18

142

0

0

The correct meshing conditions for helical gears are that the normal modulus of two helical gears is equal, the normal pressure angle of two helical gears is equal, and the helix angle of two helical gears is equal in size and opposite in direction. These conditions are the foundation for the normal operation of helical gears.As a special type of...

roy

2024-07-17

98

0

0

How to reduce sound source noise in hydraulic press?

Vasili

2024-07-16

142

1

0

What are the lubrication methods for gear reducersGear reducer is a mechanical device that uses various levels of gear transmission to achieve the purpose of speed reduction. If the friction and wear of the gears in the gear reducer are not lubricated, it is easy to cause damage to the mechanical equipment. Therefore, lubrication of the reducer is ...

Terrelle

2024-07-15

131

1

0

In order to produce highly precise products, the fourth axis accurately defines the motion of the worktable and cutting tools of the machine tool, especially the spatial position of the worktable and cutting tools, using coordinate values, and describes the motion in multidimensional space using digital information.Common fault diagnosis of the f...

Williams

2024-07-11

116

1

0

1. The working pressure imbalance of the machine tool hydraulic systemThe working pressure imbalance of the hydraulic system is manifested as unstable pressure, delayed pressure conversion, and high unloading pressure. The cause of such malfunctions is caused by hydraulic pumps and valves. The phenomenon of trapped oil in hydraulic pumps has not be...

Marshall

2024-07-10

94

0

0

1、 Strengthen the management of hydraulic oilAccording to incomplete statistics, system failures caused by hydraulic oil pollution account for approximately 70% of total failures. The pollution of hydraulic oil mainly includes impurities such as small solid particles and colloidal products, as well as water and air. Particles and other impurities a...

Smith

2024-07-03

107

1

0

Gear reducer, as a common transmission device, plays an important role in industrial production. However, sometimes we encounter situations where the motor rotates but the gears do not rotate. This article will analyze the causes of this problem and provide corresponding solutions.Cause analysis:1. Excessive gear friction: It may be due to poor l...

Gilbert

2024-06-25

114

1

0

Wheel drive is the most commonly used transmission method in mechanical equipment, widely used in various industries. As a gear device for transmitting motion and power, it plays an important role in almost any large-scale equipment.1. A pair of gears that mesh with each other will experience periodic changes in the elastic stiffness of their tee...

Liam

2024-06-21

108

1

0

What measures are taken to prevent gear pitting?

Darren

2024-06-17

95

2

0

1. The pump is difficult to suction liquidreasonThe motor does not rotateElectric motor reversalMedium viscosity too highThe suction height exceeds the allowable rangeAir leakage or blockage in the suction pipelineSolutionCheck the power supply, wiring, and motorAdjusting the phase sequence of the motorLower the temperature of the mediumReduce suc...

JOST

2024-06-11

101

1

0

Judging replication method: Along the axis of the helical gear, looking towards the direction of the external helical gear development, the helix forms a diagonal line from the bottom left corner to the top right corner, that is, the direction of clockwise movement; The opposite is also true.The helical gear has a compact center distance and can ...

Durell

2024-06-05

102

1

0

To understand the advantages of synchronous belts and chain drives, it is necessary to first have an understanding of both. Synchronous belt drives are generally composed of driving wheels, driven wheels, and transmission belts tightly fitted to the two wheels. By utilizing intermediate flexible components, rotational motion and power are transmitt...

Nugent

2024-06-03

99

1

0

Four column hydraulic presses are widely used in the pressing process of plastic materials. Such as extrusion metal forming, sheet stretching, horizontal pressing, bending pressing, correction and other processes. The common faults in hydraulic systems are relatively precise components, and the fault point is not only difficult to determine but als...

Williams

2024-05-30

100

1

0