Polski

Significant progress has been made in the manufacturing and measurement of EUV lithography light source collection mirrors

103
2025-04-02 15:30:55
Zobacz tłumaczenie

Summary:
To filter out infrared light from the driving light source in the extreme ultraviolet lithography (EUVL) light source system, a rectangular grating structure needs to be fabricated on the surface of the collection mirror. However, the collection mirror grating usually undergoes deformation during the manufacturing process, resulting in a decrease in filtering efficiency. The process errors of grating height and upper base angle need to be controlled within ± 13nm and 0.016 °, respectively, which puts extremely high demands on the measurement method. This article proposes a fast and non-destructive measurement method for collecting mirror grating deformation structures to meet their extreme manufacturing requirements.

EUV collection mirror grating structure for infrared filtering (background introduction)
At present, the most advanced commercial EUV lithography machines use laser generated plasma light source systems. In this system, a driving laser from the infrared (IR) band strikes the droplet tin target twice, causing complete ionization and generating EUV radiation. After being collected and reflected by the collection mirror, EUV radiation is focused onto the central focal point to enter the subsequent optical system.

However, in the process of collecting and focusing EUV, IR light from the driving laser is usually introduced. The energy of IR light is extremely high and will propagate along the entire EUV lithography system until it reaches the surface of the wafer. This not only causes damage to optical components, but also results in severe optical distortion and decreased pattern accuracy in the final lithography pattern. In order to filter out IR, a rectangular grating needs to be fabricated on the collection mirror substrate to diffract IR from the 0th order to higher orders, and a diaphragm is used to block the high-order diffracted light, as shown in Figure 1 (a). However, rectangular shapes are prone to deformation during the manufacturing process, resulting in asymmetric trapezoidal structures, as shown in Figure 1 (b), which reduces the infrared filtering capability of the grating. Therefore, it is necessary to analyze the deformation structure of the collection mirror grating to determine its tolerance range, and establish a model to achieve fast and accurate non-destructive measurement.

Figure 1 Schematic diagram of EUVL light source system and deformation structure of collecting mirror grating: (a) Principle diagram of collecting mirror grating filtering, (b) Collect a schematic diagram of the deformation structure of the mirror grating.

Measurement model of EUV collection mirror grating deformation structure (core content of the article)
Recently, Lin Nan's team from the Chinese Academy of Sciences Shanghai Institute of Optics and Mechanics proposed a fast and accurate nondestructive measurement method for the deformed structure of EUV collecting mirror grating. The article first establishes an efficient and accurate scalar diffraction model for collecting deformation analysis of mirror gratings, targeting the deformation structure of gratings. Secondly, propose a two-step measurement method. The first step is to quickly screen whether the key dimension parameters of the grating meet the tolerance requirements; The second step is to quantitatively reconstruct the size parameters of the gratings selected as unqualified. This method provides a new solution for the inverse scattering problem in collecting mirror grating measurements. It does not require complex numerical calculations and dependence on large datasets, while still providing accurate measurement results, which is beneficial for achieving online non-destructive measurement of collecting mirror grating structures.

The results were published in Optics and Lasers in Engineering (Yunyi Chen, Zexu Liu, Nan Lin. Computational metrology method of collector mirror for EUV lithography [J]. Optics and Lasers in Engineering 189 (2025) 108946). https://doi.org/10.1016/j.optlaseng.2025.108946
A scalar diffraction model was established for the common deformation structure of the collection mirror grating (i.e., asymmetric trapezoidal structure) to achieve tolerance analysis in order to obtain a reflectance size with IR less than 0.2%. Compared to the vector diffraction method, this model has a computational speed increase of nearly 5 orders of magnitude, and its normalized root mean square error is only on the order of 10-3. The analysis results indicate that the height and top tilt angle of the grating have a significant impact on the IR reflectivity, with a tolerance of ± 13 nm for height and only 0.016 ° for top angle.

To meet the extreme measurement requirements of collecting mirror gratings, a two-step measurement model based on optical scattering method is proposed, as shown in Figure 2. This model reconstructs the zero order and ± one order of the grating as measurement signals. The first step is to establish a "Go, No Go" model based on short-time Fourier transform (STFT), and detect whether the key size parameters of the grating meet the tolerance requirements by analyzing the spectral mutation positions and numbers in the time-frequency diagram. Qualified gratings will no longer undergo quantitative reconstruction, thereby reducing unnecessary calculations. Under the condition of a signal-to-noise ratio of 500:1, the model can achieve an accuracy of 91.3%, as shown in Figure 3 (a), and improve the overall model efficiency by at least one order of magnitude. In the second step, an improved multi-objective particle swarm optimization (MOPSO) model was further established for the detection of non-conforming gratings to achieve quantitative reconstruction of key dimensional parameters of the gratings. Under the same noise environment, the relative error of the reconstructed height of the model is only 0.19%, and the relative error of the vertex angle is only 0.84%, as shown in Figures 3 (b) and (c). The results fully meet the tolerance requirements of the collection mirror grating.


Figure 2. Flow chart of two-step measurement method


Figure 3. Refactoring Results: (a) The detection results of the "Go No Go" model, (b) MOPSO's reconstruction results of grating height, (b) MOPSO reconstruction results of grating vertex angle

Summary and Prospect (Future Development Prospects, Directions for Further Improvement)
This article comprehensively studies the inverse scattering measurement method in EUV collection mirror grating structure measurement, including the characterization of grating structure, optical diffraction model, and grating reconstruction method. The proposed method avoids complex numerical calculations, dependence on large datasets, and the need for model training, while ensuring high accuracy and efficiency, making it an ideal solution for online measurement and collection of mirror grating structure parameters. At the same time, the proposed method has a very wide range of applications, especially in the field of shortwave measurement, such as using EUV and X-rays as measurement light sources.

Source: opticsky

Powiązane rekomendacje
  • Japan's Murata Machinery Launches a Punch and 4kW Fiber Laser Integrated System

    Recently, Murata Machinery USA, a representative Japanese manufacturer of machinery and CNC machine tools, announced the launch of the latest cutting-edge punch and fiber laser integrated equipment - MF3048HL. This integrated machine combines the advantages of punch operation and laser cutting technology, eliminating the need for separate settings or material transfer between machines.Muratec's pu...

    2023-09-01
    Zobacz tłumaczenie
  • IPG Q1 revenue of $252 million, co-founder and new CEO of Jiaobang

    Recently, IPG Photonics, a high-performance fiber laser supplier in the United States, released its first quarter financial report as of March 31, 2024.The financial report shows that IPG Photonics revenue in the first quarter was 252 million US dollars, a year-on-year decrease of 27%; The net profit was 19 million US dollars, a year-on-year decrease of 75%. The change in foreign exchange rate res...

    2024-05-07
    Zobacz tłumaczenie
  • Northeastern University of Japan: Breakthrough Laser Technology for Nanoscale Laser Processing

    In the fields of optics and micro/nano processing, precise manipulation of lasers to meet the growing demand for miniaturization is an important challenge in driving the development of modern electronic and biomedical equipment. Recently, researchers from Tohoku University in Japan successfully demonstrated the use of interference technology to enhance the longitudinal electric field of radially p...

    2024-04-12
    Zobacz tłumaczenie
  • Shanghai Microsystems Institute has developed a high-speed photon detector with distinguishable photon numbers

    Recently, Li Hao and You Lixing's team from the Chinese Academy of Sciences Shanghai Institute of Microsystems and Information Technology developed an ultrahigh speed, photon number resolvable optical quantum detector with a maximum count rate of 5GHz and a photon number resolution of 61 by using the sandwich structure superconducting nanowires and multi wires working in parallel. The related rese...

    2024-07-12
    Zobacz tłumaczenie
  • Laser giant seeks $100 million financing for $422 million debt restructuring

    On August 6th local time, Luminar, a leading publicly traded company in the field of LiDAR, announced a $422 million debt restructuring and raised $100 million in new capital. This measure marks Luminar taking solid steps in optimizing its capital structure and enhancing its financial stability.In early May this year, this laser radar manufacturer released an open letter disclosing a major strateg...

    2024-08-09
    Zobacz tłumaczenie