Hello ,I use lightburn for quite some time , awesome piece of software.Although I like it and i use it very much , for the love of God and all the Angels in the heaven why is it so hard to put a lead in on the inside of a rectangle or other shapes. On circles is super easy , just put a negative angle , length and presto , inside lead in.On ...
2023-08-2136710have a k1 36 watt,power led bar registered full power when lightburn was set to 100%but now machine laser head output led bar is only showing 75-80 %
2023-08-2136710Laser chiller is one of the important accessories of laser equipment, its role is to cool the laser, so that the laser can work stably. However, if the laser water chiller leaks, it will cause great damage to the equipment, so when our laser water chiller leaks, we must find out the cause of the leakage and solve the leakage problem in time. Next, ...
2023-08-2131410Just a quick, simple question for this. I didn’t want to ruin it by experimenting to see what works best.I have to raise the laser on my D1 Pro 20w for it to go over the lip of this tray. Should I adjust the power and/or the speed to accommodate the lift?
2023-08-1529420I have downloaded the trial version of the program.I followed the set-up instructions including the import file from XTool and the first video tutorial yesterday and got a cute little key ring.Then later went back to do some more work and computer would not work with software.Showed I was disconnected from the XTool D1 Pro.Even th...
2023-08-1739710Hi, Can anyone give me a hint as what is going on here? for an unknown reason my gantry crashed in the top frame of my laser( Falcon 2 22w ) and since then it refuses to frame correctly it sometimes behaves like the laser frame is upside down ! or way over to the right! or over to the left, in frustration I reloaded my Prefs from previous save, no ...
2023-08-1724410Hello, I just upgrade my software to 1.4.01 and now my machine never ends a cut as get frozen on M2 command. The progress bar says busy and the timer keeps counting. If I press the stop button manually it doesn’t do anything and the machine is always on busy. I cannot move or home or anything. Does someone knows how can I solve this.
2023-08-1723510With each discrete step that a stepper motor makes, the inertia of the system causes the motor to slightly overshoot (or undershoot) the intended step angle. The motor then oscillates, or “rings,” until it finally settles at the commanded position. If the frequency of these step-by-step oscillations is at or near the motor’s natur...
2023-08-1724010Hello Everyone,First, I did conduct a search here and did not find an answer that solved my issue (wanted to make sure you knew that). :grinning:After switching from upper right origin to lower left origin in Device Settings, text is upside down and backwards and the Job Origin is not where I select it to be.Using Lightburn 1.4.01 on a Mac Studi...
2023-08-1634210I’m a newbie to this software.Can I use a barcode scanner to read barcodes directly into Lightburn?I am not trying to create a barcode but read an existing barcode and put the characters in to Lightburn.
2023-08-1635610Hi there, I have a fiber laser 60w JPT, I recently sttarted using it and dont have much experience, I tried engraving a mug, and found that the image was stretched accross half the diameter of the mug, It would seem that the speed of the rotary may be a problem but not sure how to set or correct this to suit.
2023-08-1624620Gearmotors use gears to reduce speed, which makes more torque available. The kind of gears used in gearmotors have an impact on the available torque, but also on things like noise levels and accuracy. In fact, one of the more common sources of inaccuracy in gearmotors is due to gear backlash. So reducing the amount of backlash will lead to a more a...
2023-08-1622711Delta Line has expanded its offering of motors with integrated electronics to include stepper motors. These smart stepper motors eliminate the need for a separate drive and controller, providing a complete stepper motor solution in a single, easy-to-integrate device.Delta Line’s ISI57 and ISI60 stepper motors with integrated electroni...
2023-08-1622610HelloI no longer have the color palette on my software at the bottom of the page I can not find it anywhere in the tabs impossible to use my laser cutting thank you for your help.
2023-08-1622910HII have an Atomstack A10 Pro with 10w laser.I’ve seen videos on youtube that cuts 10mm plywood at a speed of 200 and a power of 80% with 3 passes but I can’t even cut 6mm.Could it be some Lightburn setting?
2023-08-1531310
- Sem Dados
Português
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski