does anyone ever tested or know if laser model Ortur 2pro s2 10w work for cutting frosted arcylic 5mm?will be thankfull for an answer and if it cant do this can anyone suggest me a model that doesnt cost a lot and is good at cutting frosted & transparent arcylic 3-5mmthanks in advance im just trying to ,learn

Clarence

2023-09-07

315

1

0

After loading an image into lightburn, I should be able to hold the shift key and roll my mouse wheel to zoom in or out. As soon as I move the nouse wheel, my image immediately becomes small, then tiny. Then I have to start over again by importing image back into lightburn. Not sure why this happens. It may be the mouse/computer. I have an x-tool n...

Terrelle

2023-09-07

326

1

1

This week, PowerPhotonic, a British developer and manufacturer of free-form wafer-scale optics, introduced a new Bessel beam generator at the SPIE Sensors and Imaging exhibition in Amsterdam, the Netherlands.According to reports, the device can achieve a "diffractive output beam profile." Bessel beams have a wide variety of applications, includin...

Payson

2023-09-07

248

1

1

Constructing a continuous laser source with a device area of less than 1 μm2 can meet the low energy requirements of on-chip optical interconnection (< 10 fJ bit−1) is of great significance. However, as the device size decreases, optical and material losses increase significantly, so achieving sub-micron device size and continuous o...

Nugent

2023-09-07

279

1

0

Looking for a quicker way to do this, I have tried all the tools (Boolean Assist ) and I don’t get the results I need. I have to duplicate the rectangle because it will not stay whole with these tools. Is there a “one click” tool that will do this?

Keegan

2023-09-06

445

1

0

Hello greetings to all, how do I correct “Out of Limit Cut” in LightBurn?

Marshall

2023-09-06

329

1

0

I am going to mount the Atomstack to a bench as I will be adding a Yaxis rails, Once I am affixed to the bench I would like the laser to start at the Yaxis 0 on the machineruler and the same with the Xaxis set to the 0.I want to place two register boards one horizontal and one vertical, this makes sure my cut is square with my world.

Kevin

2023-09-06

215

1

0

Following its success at ATX East, laser innovator Luxinar will proudly showcase its latest advances in laser technology for cutting, drilling and marking in Booth 1830 during ATX Minneapolis, USA (scheduled for October 10-11).New SR e Series and SR x Series - High quality and high speed processing The SR e 9.3µm series CO 2 laser sou...

Abel

2023-09-06

371

1

0

Recently, nano and microdisk lasers have emerged as potential light sources and probes for different applications in the biomedical and nanophotonics industries. Their ability to obtain lasers with ultra-narrow band accuracy and deterministic wavelengths is important for diverse applications such as on-chip bioimaging, on-chip photon communication,...

Williams

2023-09-06

227

1

0

I have a D1 Pro 20w and using LightBurn. When I do my burns the laser moves up and down instead of side to side. Is that how it’s supposed to burn? If not…what’s the deal?!(See how the burn marks are vertical instead of horizontal)

Jen

2023-09-05

380

1

0

Im downloading ai/vector/svg files from adobestock. Saves as ai file, when i try to open in lightburn i get pop up “this file is an embedded postscript file, and is not supported by LightBurn”. Didnt have this problem before so wondering how to fix. Thanks!

John Trant

2023-09-05

202

1

1

im engraving on a large tumbler with a rotary with the comgrow z1 10w diode. the rotary replaces my Y axis on the z1Y axis looks fine, so this new rotary should be fine, right? however, X-axis seems to be skipping? not sure what the term is…im using Offset Fill instead of Fill to save time:this is what it is supposed to look like.any h...

Vasili

2023-09-04

303

1

0

I’m hoping to create a raised letting ink stamp.Can someone tell me the best way to create a rectangle around these letters, then tell Lightburn to cut around the letters to until it reaches the rectangle?

Nugent

2023-09-04

236

1

0

I’ve download a few patterns from La Hobby Guy. Some of the files are DXF and they don’t appear in the window that shows files available to load in the art library. Only lbart.However if I go the file, open in Lightburn, I can open fine. Can DXF files be loaded in the art library?Thanks!

Christian

2023-09-04

193

1

0

On August 29, Huawei threw a bombshell - Huawei MATE 60 pro, which was sold out in less than an hour. The reason why the opening of the new model set off waves in the industry, mainly because at the beginning, China's high process chip was blocked by Western countries, directly let Huawei's performance "shock", and this action may mean that Huawei ...

jessie

2023-09-04

280

1

0