chanelink logo
CHANELINK
Português

TSMC's first European wafer fab receives € 5 billion subsidy for construction

136
2024-08-26 13:41:59
Ver tradução

Recently, TSMC held a groundbreaking ceremony for its first European 12 inch wafer fab. It is reported that the European Union has approved Germany to provide 5 billion euros in subsidies for the factory.

It is understood that TSMC's 12 inch wafer fab is located in Dresden, Germany and is called "European Semiconductor Manufacturing Company (ESMC)". In August 2023, TSMC announced a partnership with Bosch, Infineon, and NXP to jointly invest in the establishment of ESMC. TSMC holds a 70% stake and is responsible for operations, while Infineon, NXP, and Bosch each hold a 10% stake, with a total investment of approximately 10 billion euros.

The wafer fab is expected to introduce 28/22 nm planar complementary metal oxide semiconductor (CMOS) technology and 16/12 nm fin field-effect transistor (FinFET) processes, with an initial monthly production capacity of approximately 40000 12 inch wafers. According to the planned construction schedule, the factory will start construction in the fourth quarter of 2024, with equipment expected to enter the factory in the third quarter of 2026 and mass production starting as early as the fourth quarter of 2027.

It is worth noting that at the foundation ceremony, EU Executive Committee President von der Leyen announced that the EU has approved to provide 5 billion euros of subsidies for Dresden wafer factory.

In fact, in addition to building factories in Germany, TSMC is also investing heavily in setting up factories in the United States and Japan. However, industry insiders point out that TSMC's expansion overseas will face a series of challenges, including high operating costs, labor shortages, cultural differences, and more. For example, the German Silicon Valley Association reminds that the German labor union has a strong and tough attitude, which is one of the challenges that TSMC must overcome.

Source: Yangtze River Delta Laser Alliance

Recomendações relacionadas

  • Internationalization Strategy Enters Stage 2.0 | HSG Hsglaser Thailand Manufacturing Base Holds Grand Opening

    At 9:00 am local time on June 26th, the opening ceremony of Hsglaser Thailand Manufacturing Base was grandly held in Bangkok Industrial Park, Thailand. This not only marks a significant expansion of Hsglaser's global strategic map, but also signifies that its international layout has officially entered a new 2.0 stage, and is another important milestone for Hsglaser to showcase its outstanding str...

    2024-06-27
    Ver tradução

  • Scientists decipher the code for extending the lifespan of perovskite solar technology

    The latest research led by the University of Surrey shows that alumina (Al2O3) nanoparticles can significantly enhance the lifespan and stability of perovskite solar cells, extending the service life of such high-efficiency energy devices tenfold.Although perovskite solar cells have advantages such as low cost and light weight compared to traditional silicon-based technologies, their commercial po...

    03-03
    Ver tradução

  • Tsinghua University has made progress in the field of magnetic field and laser composite processing

    The National Key Laboratory of Interface Science and Technology for High end Equipment at Tsinghua University has made progress in the field of magnetic field and laser composite processing - magnetic field assisted laser shock strengthening of Ti6Al4V alloy. The relevant research was published as a cover article titled "Magnetic Field Assisted Laser Shock Peening of Ti6Al4V Alloy" in the journal ...

    2023-09-16
    Ver tradução

  • A German 3D printing company applies for bankruptcy

    On February 5th, it was reported that Q BIG 3D GmbH filed for bankruptcy on January 31, 2025. The Ludwigsburg District Court has ordered temporary bankruptcy administration and appointed Mr. Ilkin Bananyarli of PLUTA Rechtsanwarts GmbH as the temporary bankruptcy administrator.The company was founded in 2019 and focuses on large format particle 3D printing systems, providing additive manufacturing...

    02-06
    Ver tradução

  • 10.30 Shenzhen Munich South China Laser Exhibition awaits you

    The Munich South China Laser Exhibition is about to open!As a member exhibition of the South China International Intelligent Manufacturing, Advanced Electronics, and Laser Technology Expo (referred to as "LEAP Expo"), it will be held from October 30 to November 1, 2023 at the Shenzhen International Convention and Exhibition Center (Bao'an New Hall) in conjunction with the Munich South China Elect...

    2023-10-26
    Ver tradução