chanelink logo
CHANELINK
Русский

TSMC's first European wafer fab receives € 5 billion subsidy for construction

128
2024-08-26 13:41:59
Посмотреть перевод

Recently, TSMC held a groundbreaking ceremony for its first European 12 inch wafer fab. It is reported that the European Union has approved Germany to provide 5 billion euros in subsidies for the factory.

It is understood that TSMC's 12 inch wafer fab is located in Dresden, Germany and is called "European Semiconductor Manufacturing Company (ESMC)". In August 2023, TSMC announced a partnership with Bosch, Infineon, and NXP to jointly invest in the establishment of ESMC. TSMC holds a 70% stake and is responsible for operations, while Infineon, NXP, and Bosch each hold a 10% stake, with a total investment of approximately 10 billion euros.

The wafer fab is expected to introduce 28/22 nm planar complementary metal oxide semiconductor (CMOS) technology and 16/12 nm fin field-effect transistor (FinFET) processes, with an initial monthly production capacity of approximately 40000 12 inch wafers. According to the planned construction schedule, the factory will start construction in the fourth quarter of 2024, with equipment expected to enter the factory in the third quarter of 2026 and mass production starting as early as the fourth quarter of 2027.

It is worth noting that at the foundation ceremony, EU Executive Committee President von der Leyen announced that the EU has approved to provide 5 billion euros of subsidies for Dresden wafer factory.

In fact, in addition to building factories in Germany, TSMC is also investing heavily in setting up factories in the United States and Japan. However, industry insiders point out that TSMC's expansion overseas will face a series of challenges, including high operating costs, labor shortages, cultural differences, and more. For example, the German Silicon Valley Association reminds that the German labor union has a strong and tough attitude, which is one of the challenges that TSMC must overcome.

Source: Yangtze River Delta Laser Alliance

Связанные рекомендации

  • The world's first 40000 watt groove laser cutting machine is put into production in China

    On the morning of August 26th, the world's first large-scale 40000 watt groove laser cutting machine production ceremony was successfully held at Shandong Century Zhenghua Metal Technology Co., Ltd. located in Zhoucun District, adding another boost to the rapid development of Zhoucun's stainless steel industry chain.Source：博览新闻

    2023-08-28
    Посмотреть перевод

  • Trumpf and SiMa. ai collaboration to develop AI laser

    Recently, Trumpf Group, a leading global provider of machine tools and laser technology solutions, announced that it has partnered with software company SiMa AI has signed a partnership agreement to develop lasers with artificial intelligence (AI).It is reported that SiMa. ai is a software centric embedded edge machine learning chip system company, and the goal of both parties is to equip Trumpf'...

    2024-07-19
    Посмотреть перевод

  • Shanghai Institute of Optics and Mechanics proposes a new scheme of Er doped silicate fiber as an extended L-band broadband amplifier

    Recently, Hu Lili, a research group of the Advanced Laser and Optoelectronic Functional Materials Department of the Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, proposed a new scheme based on field strength optimization of Er doped silicate fiber as an extended L-band broadband amplifier. Relevant research achievements were published in Optics Letters under the tit...

    2024-06-05
    Посмотреть перевод

  • Improvements in LiDAR technology will help NASA scientists and explorers perform remote sensing and measurement functions

    Improvements in LiDAR technology will assist NASA scientists and explorers in remote sensing and measurement, surveying, 3D image scanning, hazard detection and avoidance, and navigation.Like sonar that uses light instead of sound, LiDAR technology is increasingly helping NASA scientists and explorers with remote sensing and measurement, surveying, 3D image scanning, hazard detection and avoidance...

    2023-10-26
    Посмотреть перевод

  • Scientists plan to build particle accelerator to power giant chip factory

    Scientists are exploring new ways to get around limitations on the lithography machines used to produce microchips. Researchers are using particle accelerators to create new laser sources that could lay the foundation for the future of semiconductor manufacturing.Plans are underway to build a particle accelerator with a circumference between 100 and 150 meters (328 and 492 feet), about the size of...

    2023-09-25
    Посмотреть перевод