The main parameters of industrial cameras include resolution, frame rate, signal-to-noise ratio, pixel depth, etc. In addition, other important parameters also include dynamic range.Dynamic range refers to the brightness range in the scene or the photosensitive range of photosensitive materials such as film, CCD, CMOS, etc. For film and pho...

Tim Johnson

2023-11-30

120

1

0

Laser cleaning technology is a new type of clean and environmentally friendly cleaning and processing technology that has emerged in recent years. Its working principle is to use a high energy laser beam to irradiate the surface of the material, so that the irradiated pollutants expand and evaporate, so as to achieve the purpose of removing stains....

Christian

2023-07-25

336

1

0

From the point of view of concern, motor control (here refers to servo motors) is mainly concerned with controlling one or more parameters in the rotation, speed, and position of a single motor to reach a given value. The main focus of motion control is to coordinate multiple motors to complete the specified motion (synthetic trajectory, synthetic ...

Kevin

2023-07-20

319

1

0

What are the reasons why the motion control card is not linked

Tory

2023-07-08

234

1

0

We all know the three-ring, in which the current ring is adjusted by the driver itself, we need to do the work is to adjust the outside speed ring and position ring, inside this is the classic PID control,When we carry out positioning control, the speed curve and displacement curve will be planned in advance, and then the PLC is sent to the servo ...

Keegan

2023-04-04

276

1

0

High precision motion control, that is, to produce the fastest and smoothest time trajectory as far as the mechanical structure allows.How do you do that?Determine the algorithm under system constraintsMeanwhile, the complexity of the algorithm is also restricted by the real-time performance of the system and the speed of the computerUsual...

Kevin

2023-03-30

245

0

0

Two cylinders hold up one frame on each side. If one of the cylinders is slow the shelf will be forced on one side. I've been thinking about it for a long time and it seems like it's impossible to synchronize the two cylinders, even if the pressure is the same, the piston will not be as tight as it should be over a long period of time, causing it t...

Patrick

2023-03-29

395

1

0

For example, Mitsubishi FX20GM module, compared with PLC pulse output control has what advantages?

Christian

2023-03-22

217

1

0

If you use m0 to drive the ddrvi command to cause the servo action to travel 10000 pulses, and if the command is not fully executed (6000 pulses have been driven), m0 is disconnected. When m0 continues to be connected, do you want to travel 4000 pulses or 10000 pulses?

Marshall

2023-03-21

323

1

0

Do you want to use an emergency stop to power off, to disable all outputs, or to use an emergency stop to pause in the program?

Kevin

2023-03-21

235

1

0

I have a set of B2 servo in my hand. I would like to ask how to use B2 to control the motor for some simple movements, such as controlling the screw module from point A to point B (taking 10 seconds).

Terrelle

2023-03-20

328

1

0

Set the number of pulses per servo turn. When the lead screw stroke is 32mm, the servo setting is 3200 revolutions per turn, and the maximum output of the PLC is 100K. In this way, the maximum speed of the servo can only be 1850 revolutions. How can the maximum speed be 3000 revolutions?

Vasili

2023-03-17

293

1

0

The closed-loop controlled frequency converter can achieve closed-loop position control in the stopped state through encoder detection, locking the servo motor shaft at a fixed angle. This function is called servo motor locking or zero servo function.

Keegan

2023-03-18

236

1

0

One equipment on the production line and one servo are transplanted to the normal position. It has been determined that there is no problem with the mechanism. It should be an interference problem. The servo is Panasonic servo motor. I don't know how to eliminate this problem?

Vasili

2023-03-13

279

1

0

The can is broken, and the pressure is rhythmic. This is the hydraulic part.On the other hand, the servo motor follows the rhythm of the energy storage tank and goes off and on.Oil and electricity are irrelevant.

Keegan

2023-03-10

306

1

0