Hi there I am new to laser welding We weld aluminum with 2mm thickness The protective lens burnt so fast i change it 3 to 4 time a dayUsing 2000W fiber laser welding machine from depang model number dph-2000So any help to solve the problem
2024-03-1018050When using a servo (Panasonic) to return to the origin in a recent project, if other axes are also moving, the Z-phase zero point signal received by the PLC is easily lost, resulting in abnormal return to the origin position. Later, upon checking the driver manual, it was discovered that the GND of the Z-phase zero point signal needed to be connect...
2024-03-1117720As an indispensable supporting equipment for most lasers, laser chillers are responsible for cooling and cooling the laser. Matching a suitable laser chiller can provide good cooling effect for the laser and ensure its efficient operation. When the laser chiller works for a long time, the cooling effect decreases and the water temperature is not co...
2024-03-11124101. Gear operation generates heata. Overload or ultra high speed.The driving load is too large, causing an increase in gear meshing sliding heat generation.b. Insufficient or incorrect selection of lubricating oil/grease.Too little lubricating oil/grease can cause oil film failure and increase meshing friction. In addition, improper use of lubricant...
2024-03-1113710I recently bought a dual beam co2 laser with a camera. The machine has a ruida RDC6685U controller installed and the software is RDVisionWorks. The way it's supposed to work is the camera takes a picture of the printed fabric, identifies the outline and then cuts. After the cut, it moves on the U-Axis and repeats the action until the job is complet...
2024-03-1226610Will laser cutting replace CNC and wire cutting?
2024-03-0914020What speed curve has the highest stability when the servo motor starts or stops. The commonly used trapezoidal velocity curve has significantly poor stability. It is said that according to the 5th degree curve acceleration, the motor torque will not experience sudden changes, and the motor stability is also more reliable?
2024-03-09142101. Transition curve interferenceTransition curve interference refers to the interference at the transition curve between the tooth tip of a gear and the tooth root of the matched gear during the meshing process.2. In order to prevent interference in the transition curve during the meshing process, the selected meshing parameters must ensure...
2024-03-0911310Industrial chillers are undoubtedly familiar to friends in the manufacturing industry. A chiller is a cooling device that provides cooling and cooling for industrial production equipment such as chemical, mechanical, food, microelectronics, and laser processing.During operation, industrial chillers can output ice water that is lower than the ambi...
2024-03-0911610The ultraviolet laser marking machine is a cold processing method, where high-energy molecules in ultraviolet light directly detach the molecules on the metal or non-metal materials that need to be processed, causing the molecules to separate from the material.Electronic mobile phone components, LCD screen engraving QR codes and trademarks, ceram...
2024-03-0813210Steel can be said to be ubiquitous in daily life, but it has a disadvantage that it is prone to rust, especially those without paint or coating protection.Laser is another major invention of humanity since the 20th century, following nuclear energy, computers, and semiconductors. It is widely used in many fields and is known as the fastest knife, ...
2024-03-0812010How many W servo motors can drive a 300kg load to move horizontally?
2024-03-0715320What is the difference between chain conveyor and gear drive?
2024-03-07137101. Examination of the entire bedBefore starting up every day, check the wiring of the laser cutting machine and the outer cover of the entire machine for any abnormalities. Start up the main power supply, power switch, voltage stabilizing equipment, air-cooled machine, laser, and auxiliary system to ensure that these overall components are intact a...
2024-03-0715110The running trajectory is incorrect, occasionally taking an extra half turn and deviating. Occasionally, there is an abnormality in not turning off the light.Problem analysis: Generally, it is a program problem. Determine whether different devices have been used and whether there is any unreasonable interaction between the customer's device...
2024-03-0716810
- Không có dữ liệu
Tiếng Việt
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski