In servo torque mode, the speed limit value is controlled by analog quantity, and the torque limit signal is used to achieve the purpose of screwing.At present, the problem is: when the torque limit signal is output, you want to judge whether it is screwed in place. How do you realize this working condition? What is the convenient way?In addition, ...
2023-03-0429310Panasonic MSMF series servo motors, 50W and 100W are all suitable for the same type of drive. The original 50W motor is used, but now the 100W motor is replaced. Is its current, torque and other parameters adaptive? Does the torque monitor output signal including IM terminal correctly reflect the motor torque after replacement?
2023-03-0224710Today, I measured two dozens of Ford and several hundreds of Ford. Why is the three-phase unbalance?
2023-02-2035910Torque motor is a special type of brushless permanent magnet synchronous motor. Since the load is directly connected to the rotor and no transmission parts are required, the torque motor belongs to the direct-drive motor.The following is the difference between torque motor and servo motor:Different performance1. Torque motor: a special mot...
2023-02-17336001. Initialization parametersInitialize parameters before wiring. On the control card: select the control mode; Clear PID parameters to zero; When the control card is powered on, the enable signal is turned off by default; Save this state to ensure that the control card is in this state when it is powered on again.On the servo motor: set the...
2023-02-1614500What work needs to be done before starting the servo motor1) Measure the insulation resistance (not less than 0.5M for low-voltage motors).2) Measure the power supply voltage and check whether the motor wiring is correct and whether the power supply voltage meets the requirements.3) Check whether the starting equipment is in good condition.4)...
2023-02-1620100The servo in the industrial control industry is generally the abbreviation of AC servo system. At the project site, the servo we refer to is the servo driver. However, servo driver and servo motor are an inseparable system, and they are connected by encoder cable and power cable. Generally, the servo driver bears the control command of the controll...
2023-02-1535300How does the PLC control the servo motor to automatically move left and right The servo motor drives the linear module to move from the left to the right and then automatically returns
2023-02-1521910Introduce three control modes of servo motorIf you have no requirements for the speed and position of the motor, just output a constant torque, which of course is torque mode.If you have certain accuracy requirements for position and speed, but you don't care much about real-time torque, it is better to use speed or position mode.If the up...
2023-02-1536200Speed control and torque control of servo motor are controlled by analog quantity, and position control is controlled by sending pulse. The specific control mode should be selected according to the customer's requirements and the sports function.Next, we will introduce three control modes of servo motor1. If you have no requirements for the...
2023-02-1420600At present, explosion-proof servo motors are widely used, for example, in military, aerospace, AGV and other industries, and also in the automation equipment industry.Our company now produces two kinds of explosion-proof servo motors, AC and DC. The servo motor is simply an engine that controls the operation of the equipment in the servo sy...
2023-02-1333700What parameters do you select for servo motor? The most important is the speed, power and torque of the motor. Of course, many times we also need to consider the motion accuracy of the motor, and the choice of encoder is also careless. The accuracy of 23-bit multi-turn absolute value encoder is much higher than that of 17-bit multi-turn absolute va...
2023-02-1318100Servo motor is a type of engine, which belongs to the indirect variable speed device of auxiliary motor. Why is servo motor so important? Because this is to convert the received electrical signal into the angular velocity output or angular displacement output on the motor shaft, which is the core of a machine.The application of servo motor ...
2023-02-0430000Servo motor maintenance is divided into mechanical part and electrical part.1. The mechanical part is repaired for bearing damage replacement. Compared with the maintenance of ordinary motors, the bearing is only special. Because most servo motors are synchronous motors with magnetic poles on the rotor, common materials cannot solve the problem, s...
2023-02-0430300The failures caused by ball screw are various and have no fixed mode. Some faults are gradual faults, which need a development process and become more and more serious with the increase of service time; Sometimes it is a sudden failure, usually without obvious symptoms, but it occurs suddenly. This kind of failure is caused by various adverse facto...
2023-02-0231700
- Không có dữ liệu
Tiếng Việt
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski