My problem seems to have started after I used the rotary tool. After doing some engraving on a glass I switch to another project cutting and engraving. I discovered that my y and x axes were not accurate, so I calibrated the X axis, which went fine but I never could properly calibrate the Y axis. I read that it may be because I had to close down al...

Carey

2024-10-15

143

4

0

wen you save a material test can you please make it save the “material” “text” and "border settings as well, this wil make easyer to acurately repeat the test later on

bernd.db

2024-10-16

146

3

0

Is there any way to randomise the order of the shapes burned in the material test? The localised heat effects of ramping power/frequency/speed in the x axis tend to give unreproducible results when these are taken into consideration. I have tried putting a 0% sublayer in to reduce this, but it makes the time to run a test significantly longer.Stain...

Iron Man

2024-10-16

162

1

0

Hello,often times when I do nesting I have a form, in this case a star, and I want to align it, so that it is “standing straight”.Or there is one form, here the green one, which I want to align to another form, here the blue one, like that:Is there a feature like that? It would save me a lot of time.I know there is nesting software, but it did...

Cruise Wang

2024-10-15

179

1

0

Newbie here, I have an open frame cnc with a laser attached, blackbox controller, no limit switches. I set user origin lower left of job, run macro G92 X0 Y0$10=0set origin and return origin the same. I’m running a circle inside of a square wanting it centered in the square. The job runs correctly with the exception is the job burns approximately 3...

55455rml

2024-10-12

127

3

0

So when I engrave or cut the laser moves to the same position it starts from. When I use the rotary and engrave tumblers the laser head goes to a differant position from where it starts. This has changed since I upgraded from 1.6 to 1.7.01. How do I change so laser head parks after engraving in the same position it starts?

Noah

2024-10-11

168

3

0

Hello,I am using version 1.7.00 in English, down loaded SHX fonts from Internet, extracted to a folder, put the folder name in configuration SET SHX font path, it does not bring the SHX fonts when I type over default arial a font like “FIN”, simply it cannot find it. Any clue?

Ethan

2024-10-11

144

4

0

hello everyone,I found an example of PCB design online. In practice, the base is painted black and the paint burns out in areas where copper must be removed through reverse circuit design. Then etch with acid.The laser head must be installed on the CNC instead of the spindle, but I don't know the power and cost of this instrument.Is one of these la...

Ruddy

2024-10-14

128

1

0

I have a J-Tech Photonics 4.2-watt laser. My current value setting is 1000.My question is, what would happen if I increased each setting equally, how would this effect my laser?

Rajiv001

2024-10-12

126

1

0

I have been installing S9 for a few months now, and a few days ago I decided to give it a try.I returned to my original position, but strangely, the machine got stuck after traveling a few centimeters. I exerted a little force, and it traveled a few more centimeters before locking again.I think the strap may be too tight, so I patiently loosened it...

Rajiv001

2024-10-09

165

2

0

I built a project and set the cuts/layers speed to 10 and saved the project. I then reselected the project and loaded to the art library. When I bring the project from the art library to the workspace the speed in cuts/layers has changed. I’m using Lightburn 1.7.01 on a windows 10 laptop.

Erdogan

2024-10-10

208

1

0

Mac Ventura, lightburn 1 6 03 neje max 4Never had this problem before upgrading to lightburn1.6.03when engraving, which is most of my workflow, the laser starts each line 2mm to the left of the last, so quickly runs off the wood I am engraving. Sometimes if I rotate the engraving 90 degrees it engraved okay but id I duplicate back to the same issue...

さいと康成

2024-10-10

194

1

0

Hi,after installing the new version 1.7.01 the laser freezes when it has to draw a curve or an image and returns this error:The format of the numeric value is invalid or an expected value is missing.On or near line 0:No problems so farcan someone help me?thanks

RTP

2024-10-08

136

2

0

Why? Line nodes won’t connect to other nodes? What is the trick? And why did the nodes on a new line turn all red?

Roderick

2024-10-08

132

2

0

We are setting up a laser machine to carve copper; From the first test, for example, by digging a small square at 0 degrees, a Z-dip angle of approximately 10-15 degrees can be obtained. What parameters should we use for perfect straight line cutting?

55455rml

2024-10-09

128

1

0