1. Check for air in the chiller cooling system. When installing a chiller, there should be no air inside the unit, or the pump, or the pipeline, even a little air, and the chiller will not work normally. In addition, there is a film inside the pump, which must be torn off before installation. Otherwise, the water has no way to circulate or the circ...

Cyril

2024-05-31

104

1

0

The industry where chillers are used is very extensive, especially in industrial manufacturing. Chillers also have energy-saving and intelligent features. Understanding the normal operation signs and cooling capacity adjustment methods of industrial chillers can enable better operation of chillers. At the same time, it is important to pay attention...

Henry

2024-05-28

81

1

0

As an important equipment in modern industrial production, the operational efficiency and stability of industrial chillers cannot be ignored in their impact on the production process. After all, these details not only affect the performance of industrial chiller equipment, but also directly affect production efficiency and the service life of the e...

Patrick

2024-05-27

144

1

0

A sudden decrease in the temperature difference of a normal chiller can cause a decrease in the cooling effect of the production equipment or prevent it from working properly, resulting in product quality problems and wasting a lot of energy. So, what are the reasons for a small temperature difference in a chiller?We have a basic understanding of...

Payson

2024-05-25

107

1

0

In industrial chiller systems, the water pump is one of the important components that can provide water flow and pressure to the chiller system. Not only is the water capacity in the water tank easily affected by the water flow rate, but it is also affected by the water pump.Reasons and solutions for water pump burnout:1. Unstable power supply vo...

Darren

2024-05-24

148

1

0

Components of industrial chillers:1. CompressorThe core part of an industrial chiller is the compressor, which acts as the "heart" of the entire system. The compressor is responsible for sucking in low-temperature and low-pressure refrigerant, which is compressed into high-temperature and high-pressure gas, providing power for the refrigeration cyc...

Aaron

2024-05-23

105

1

0

1.Firstly, check the main circuit. Whether the power supply is powered on, whether the voltage is normal, whether the starting overload fuse is burnt out, whether the air switch is tripped, whether the switch contact is intact, and whether the power supply is out of phase. When starting, observe the voltmeter and ammeter. When the industrial chille...

Andre J

2024-05-20

106

1

0

It is inevitable to encounter malfunctions when using industrial chillers. Below are several common malfunctions and their causes during the use of chillersOil pressure alarm occurs during useCommon causes of oil pressure alarm in chillers:1. The internal parts of the chiller have not been inspected and cleaned, resulting in oil stains, oil pump f...

Ruddy

2024-05-16

111

1

0

During use, the performance of a chiller will gradually decrease over time. In fact, many faults have some precursors before they occur, which are commonly referred to as potential faults.The failure rate of a chiller also varies over time, which is commonly referred to as its lifespan.1. Phase 1: Early FailureEarly failures, also known as the br...

Hiroko

2024-05-15

108

1

0

1. Check the operating environment.Ensure that the water-cooled industrial chiller is placed in a well ventilated and temperature appropriate environment, avoiding direct sunlight or excessively humid environments, which helps the water-cooled industrial chiller maintain good working conditions.2. Check if the cooling water circulation system is ...

bernd.db

2024-05-14

115

1

0

1. When a water outage occurs, it is usually caused by a significant lack of cold water. In the specific application of industrial chillers, it is necessary to immediately check whether the chiller pump and all chiller control circuits are in a reliable software environment. Only by maintaining the smoothness of waterways can the probability of wat...

Marshall

2024-05-08

112

1

0

The laser is the most important core component of the laser welding machine, so the protection of the laser is very important. Therefore, the premise of doing a good job in the maintenance of the laser is to ensure that the chiller closely related to it is regularly replaced with ionized water, because the purity of the cooling water is the key to ...

Jen

2024-05-07

114

1

0

In the industrial field, there are usually two auxiliary cooling methods for laser equipment: water-cooled and air-cooled. In practical applications in the industrial industry, the commonly used ones are water-cooled. That is what we know as a chiller. The chiller can provide timely cooling for laser equipment under high temperature and heat condit...

JOST

2024-04-30

114

1

0

The E05 fault code alarm of the chiller (cold water tank) is usually caused by abnormal water flow rate, and there are usually the following reasons:1. Check if the circulating water in the laser water cooler is fully filled and if there is dust blocking the bottom filter screen. After cleaning, see if it can return to normal.2. Is there any devi...

Iron Man

2024-04-26

118

1

0

1、 Screw chiller unitThe chiller is designed with a screw compressor as the main unit. The screw chiller technology is mature in industry and is widely used in chemical, pharmaceutical, food, refrigeration, engineering construction, etc. The typical refrigeration capacity range is 700 to 1000kW.The characteristics of screw chillers include:1）Simp...

Kevin

2024-04-22

100

1

0