So I have a Creality Ender 3 S1 Plus with 5W laser module set up. It has not been cutting at its full power, because it cut the same material at the same speeds in Creality Print. So I found out that the S-Value Max setting needs to be set to your machine. My problem is I don’t know what setting to set it to. I’m including a picture of my machine s...

James

2024-11-12

141

1

0

Na het instaleren van de limitswitches wat ook de nodige problemen gaf eindelijk alles good 0 postie wordt gevonden. framen laser aan met framen. eerder kreeg een continu straal die rond het werkstuk ging en de frame aangaf van af nu knippert hij, daarnaast graveert hij dus ook niet meer snijden gaat wel goed wie weet raad

이야기 너와

2024-11-09

91

1

0

Hi, can you please advise. Is there any way to ensure that the beginning (3-5 mm) is also cut through when cutting the poplar plywood? I can increase the power or decrease the speed, but then the rest will be pretty burnt. A ramp like a cnc milling machine would be good. Thanks.

Farouk

2024-11-06

109

3

0

So I just replaced the tube in my machine and got a wattage tester to confirm its output. After a lot of careful testing, I’m finding that it is maxing out at 110ish watts on a 130 watt tube. Because of this, I’m hoping to find a way to do a system wide power scale so that if for a part I need as much power as I can get, I can put it 100% into the ...

Rajiv001

2024-11-06

115

1

0

I’m trying to cut a project 3 ft long - so using the print and cut feature. After I cut my first of the three parts (i broke the project up into 1 ft incriments) I go to align my laser with the registration marks; however, after i move my laser head to the mark and choose “set first target position”, i then frame the registration mark and the laser...

RTP

2024-10-17

114

2

0

So when I engrave or cut the laser moves to the same position it starts from. When I use the rotary and engrave tumblers the laser head goes to a differant position from where it starts. This has changed since I upgraded from 1.6 to 1.7.01. How do I change so laser head parks after engraving in the same position it starts?

Noah

2024-10-11

150

3

0

I built a project and set the cuts/layers speed to 10 and saved the project. I then reselected the project and loaded to the art library. When I bring the project from the art library to the workspace the speed in cuts/layers has changed. I’m using Lightburn 1.7.01 on a windows 10 laptop.

Erdogan

2024-10-10

189

1

0

We are setting up a laser machine to carve copper; From the first test, for example, by digging a small square at 0 degrees, a Z-dip angle of approximately 10-15 degrees can be obtained. What parameters should we use for perfect straight line cutting?

55455rml

2024-10-09

110

1

0

Im new to laser cutting / engraving so please forgive my ignorance . I have been told to use a coolant for my laser cutter . Can any of u legends give some helpful advice on the coolant i should use ?

JOST

2024-10-05

114

1

0

Hi,Just bought a fiber laser and want to download a materials parameters library from The Laser Master Academy, which have been essentially useless in helping me. So I thought I would try here because of past successes.I am on a Mac with Sonoma 14.5, I am also using LightBurn 1.6.03. I initially downloaded the document and got the message that I ...

berainlb

2024-09-25

151

2

0

I am cutting out two plywood rectangles to be glued back to back using the same rectangle drawn in Lightburn but when I fit the plywood together, it does not line up square. What am I doing wrong? Thanks!

Andre J

2024-09-14

176

2

0

hello everyone! trying out 1.7rc 7one thing ive found is it wont save cut settingshave checked and load defult layer settings on new or start up is on

Ruddy

2024-09-13

132

1

0

Hi Folks,i want to cut Parts for a Modell airplane, but there is only small differences between this parts, so i have to engrave some Numbers on them.I marked this Numbers and set them to Layer 02. In cutting options i reduced the Laser Intensity so that he only engrave this parts.But how can i set Lightburn, that its doing First the engraving and ...

Terrelle

2024-09-12

153

1

0

It is generally recommended to lubricate the laser cutting machine once per hour, and the specific time can be adjusted according to the actual situation.The function of lubricating oilLaser cutting machines require the use of lubricating oil during operation to reduce friction and wear, protect various components of the machine, and extend the s...

Jen

2024-08-29

92

0

0

1. Adjust equipment parameters:According to the thickness and type of material, increase the laser power and frequency appropriately to make the laser beam act more strongly and densely on the material. Optimize the focusing system to ensure accurate focusing of the laser beam and improve cutting efficiency.2. Optimize cutting process:Reasonably ...

jessie

2024-08-07

103

0

0