Hey Gang,All of a sudden, my 10w Creality CR Laser Falcon SE is not burning properly. It’s “missing” areas of the burn. I’ve made no changes in Lightburn but as you can see from the image example and the screenshot from LB, it’s missing. I’ve tightened the belts thinking that could be the problem. Any other ideas...

Henry

2023-08-24

249

1

0

If I try to start the laser He always Go Up first and than start .So he runs against the switch and lost the steps he need. look pic.Can Anyone Help me whit this

John Trant

2023-08-24

202

1

0

Good evening. So currently I have 2 Co2 lasers (different wattage/purpose machines), 5W UV Laser, and 50W JPT Fiber Laser Trying to figure out a way to combine all libraries into one, however have them categorized. So for example, I have a header value of Fiber, UV, Co2 and under each header then I can enter my cut/engrave settings for each of the ...

Robert Evans

2023-08-24

241

1

1

I also had a problem since downloading .01 but only on my laptop.Message isThere is a problem sending data to the laserThe machine may be busy or paused.Ran cable to my desktop and everything worked fine

Cyril

2023-08-22

243

1

0

ik kan niet het hele werk gebied van 500mmx450mm gebruikenals ik het wil gebruiken krijg ik een melding,ALARM:2G-code bewegingsdoel overschrijdt machinebeweging. Machinepositie veilig behouden. Alarm is mogelijk ontgrendeld. (Klik met de rechtermuisknop op de knop ‘Apparaten’ om de verbinding opnieuw in te stellen)Op of nabij lijn 2:.we...

roy

2023-08-17

279

1

0

Hi everyoneI am trying to make an LED light and i cant get the part I have drawn to attach to the red out line i have tried using node editor and auot join but nothing works.Any help would be great.Thankyou

Smith

2023-08-22

260

1

0

Hey there,I hope you can help me out. My laser seems not to connect (never did). LB keeps saying “disconnected” / “waiting for connection”. Even in the Device Manager nothing happens, when I connect the laser to the laptop - just nothing.Meanwhile I tried everything - I guess:twisted USB-C Cable 180°Tried another cable...

Gilbert

2023-08-22

331

1

0

I have a Ortur LM3, since adding the frame extension I have been having issues with shapes not being closed as they should be. I have checked the pully tensioners & they appear to be the same, I doubt its Lightburn but I thought some users may have seen this before I could point me in the right direction.You can see the issue in the attached i...

roy

2023-08-23

250

1

0

Which is the best choice for water-cooled, air-cooled handheld laser welding or dual circuit refrigerant direct cooled handheld laser welding?

Rajiv001

2023-08-28

375

1

0

I have traced a descent sized image in terms of L x W, so that the Trace Image feature can grab as much detail as it can.When scaling down the traced image, part of the trace disappears and there is a disconnect which can only be seen in the preview tab.Image preview when making the trace bigger and there is no disconnect:How can I make sure th...

Smith

2023-08-25

207

1

0

What does sanity check do?

Miller

2023-08-25

312

1

0

No matter how large I make the ‘Y Center’ or ‘X Center’, the generator keeps this tiny space between the cuts squares. Take a look at the screenshot. I need that gap to be larger otherwise the laser just cuts into the next line.

Darren

2023-08-25

305

1

0

HII would like to understand why the preview of the photos almost never corresponds to the final result.Show the photo always much darker and therefore you are forced to experiment, wasting a lot of time and material consumption.Solutions?

David

2023-08-24

295

1

0

New getting Missed Steps. Got a hold down magnet (quite powerful) on Stepper Motor, and also gantry obstructed on home.The belts are OK, steps only Y mainly I think…Could there be missing teeth - does not always occur.Are there settings that I could change to helpLawrence

Abel

2023-08-25

228

1

0

This is my question: I’m drawing in inkscape paths in differents colors. The closed path can be rustered, so the question is: can engrave grayscale background with “proportional power” like image engrave function?

Williams

2023-08-25

331

1

0