I’ve got an excerpt from a creation I made that the laser path optimization is playing the tune to SuperTramp’s “Take the long way home”. Can’t quite figure it out.When I have border-type fills like this, I often change to offset fill to get away from the raster whitespace. But only when it makes sense.In this creation, which happens to be a saw...

Andre J

2024-10-18

142

3

0

i have a problem with new a24 pro laser . it will connect and frame okay but when i run the file it works for about 30 seconds and then shuts down laser and locks up, i cannot do anything else until i shut down lightburn and the laser and when i try again exactly the same problem happensthe laser works perfectly on its plug in screen, and the light...

Erdogan

2024-10-14

219

6

0

Hi,I have an issue ever since I bought the Laser master 3 engraver. I cant manage to get the lines straight, the lightburn printing test doesnt even manage to engrave normal squares and I don’t know what to do in order to resolve the problem.

AL.TAL

2024-10-21

165

1

0

I’m trying to cut a project 3 ft long - so using the print and cut feature. After I cut my first of the three parts (i broke the project up into 1 ft incriments) I go to align my laser with the registration marks; however, after i move my laser head to the mark and choose “set first target position”, i then frame the registration mark and the laser...

RTP

2024-10-17

131

2

0

I fully realize that I may be doing something to cause this, but the biggest frustration I’ve faced is how LB handles layers settings when reopening a project or starting a new one. Because at times, it seems random to me.I’ve had it change for some reason right in the middle of the project when I’m only using one layer.How is it supposed to work?

Hiroko

2024-10-17

154

2

0

My problem seems to have started after I used the rotary tool. After doing some engraving on a glass I switch to another project cutting and engraving. I discovered that my y and x axes were not accurate, so I calibrated the X axis, which went fine but I never could properly calibrate the Y axis. I read that it may be because I had to close down al...

Carey

2024-10-15

145

4

0

wen you save a material test can you please make it save the “material” “text” and "border settings as well, this wil make easyer to acurately repeat the test later on

bernd.db

2024-10-16

151

3

0

90W CO2 laser single tube retrofitted with Ruida 6445G controller, started having the following problem: Output power of laser varies only up to about 25%, and beyond that stays constant.  That is, 50% power setting will provide same effect as 25% output, same for 100%. Measuring output to laser power supply (GND to LPWM1):15% = 0.73025% = 1....

8EFCC2EB

2024-09-26

276

6

0

Is there any way to randomise the order of the shapes burned in the material test? The localised heat effects of ramping power/frequency/speed in the x axis tend to give unreproducible results when these are taken into consideration. I have tried putting a 0% sublayer in to reduce this, but it makes the time to run a test significantly longer.Stain...

Iron Man

2024-10-16

166

1

0

Hello,often times when I do nesting I have a form, in this case a star, and I want to align it, so that it is “standing straight”.Or there is one form, here the green one, which I want to align to another form, here the blue one, like that:Is there a feature like that? It would save me a lot of time.I know there is nesting software, but it did...

Cruise Wang

2024-10-15

183

1

0

Newbie here, I have an open frame cnc with a laser attached, blackbox controller, no limit switches. I set user origin lower left of job, run macro G92 X0 Y0$10=0set origin and return origin the same. I’m running a circle inside of a square wanting it centered in the square. The job runs correctly with the exception is the job burns approximately 3...

55455rml

2024-10-12

133

3

0

So when I engrave or cut the laser moves to the same position it starts from. When I use the rotary and engrave tumblers the laser head goes to a differant position from where it starts. This has changed since I upgraded from 1.6 to 1.7.01. How do I change so laser head parks after engraving in the same position it starts?

Noah

2024-10-11

170

3

0

Hello,I am using version 1.7.00 in English, down loaded SHX fonts from Internet, extracted to a folder, put the folder name in configuration SET SHX font path, it does not bring the SHX fonts when I type over default arial a font like “FIN”, simply it cannot find it. Any clue?

Ethan

2024-10-11

146

4

0

hello everyone,I found an example of PCB design online. In practice, the base is painted black and the paint burns out in areas where copper must be removed through reverse circuit design. Then etch with acid.The laser head must be installed on the CNC instead of the spindle, but I don't know the power and cost of this instrument.Is one of these la...

Ruddy

2024-10-14

130

1

0

even with a 1mb jpeg photo...i get "not enough buffer space.....can cut shapes, but cant do photo engrave....6445S....i'm guessing this is a parameter.....i have 450mm x 380mm working space....even reducing photo to 100mm x100mm...immediately get this error on panel

44CFD702

2024-10-12

149

1

0