I have purchased the Lightburn 5mp-150 with Aspect 1.333. The Camera selection help table indicated that the minimum mounting 8.75". I have the camera mounted at 11’ from the laser bed and it will not capture the dot pattern. It will capture the same pattern when I raise the camera to 12" or higher.I do not have the space to keep the camera a...

Liam

2023-12-28

181

1

0

I’m just starting my new venture. How do you set up or where do you get your line mode color square usually located at the bottom of lightburn users screen. Thanks for your help. I have been in the computer world for years but am stumped on this little question.

jessie

2023-12-27

158

1

0

Hi and thank you for your time and suggestions.I’m a newbie to laser and Lightburn.Can you please suggest some of the best online box makers that I as a newbie will easily get a hold on? I’ve done some searching and some seem very easy but, for some reason have lower ratings.Thanks so long.

Patrick

2023-12-27

182

1

0

My computer crashed while engraving earlier. Image had a 1 hour 15 minute time estimate. Same engraving this morning was close to that estimate. Trying to burn image this afternoon, estimate is not 1 hour 40 minutes. Laser head doesn’t change speeds when changing settings while doing test burns.Any ideas on what setting(s) need to looked at?

Christian

2023-12-27

146

1

0

In the early automation industry, motion control was mostly pulse control and analog control. Later, CANopen was developed, and various Ethernet buses emerged, such as EtherCAT, PROFINET, POWERLINK, SercosIII, RTEX, and so on.Why is EtherCAT developing so rapidly both globally and in China now, mainly reflected in the following five points:...

Nugent

2023-12-26

144

1

0

May I ask if you are planning to use a laser displacement sensor to scan the parts, and then use a servo motor with a grinding wheel to follow the contour of the parts for polishing? How should you configure the hardware?

Vasili

2023-12-26

151

1

0

I was wondering if anyone has successfully cut anything with the 5 watt creality laser module attachment not the table and laser, the actual unit that attaches to my 3d printer. If so what speed and how many passes?

Payson

2023-12-26

133

1

0

Hello all. I hooked up my Ortur Extension to engrave longer pieces and changed my settings but when I hit Frame the laser goes to about the middle right of the project and just stops. Any suggestions? Seems to be only this particular project.

Terrelle

2023-12-26

156

1

0

I Recently Added the Falcon laser rotary roller to my 5w laser. According to the instructions that came with it. I had to enter $101=60.375. It then tells me after use to change $101 to 80. What does that mean? Also with the rotary off, and back to normal cutting, my circles are oval. I am assuming i have something wrong and cant figure it out. Nev...

Gilbert

2023-12-25

129

1

0

Hey all, I have a halfway decent PC but I notice that when I run other resource intensive programs my laser starts to stutter even though none of my resources are at 100% usage. Just wondering if there’s any setting within Lightburn to give it priority?

Cyril

2023-12-25

140

1

0

I have a new Longer B1 40w laser added the Atomstack AC1 completed the install / camera calibration / camera alignment… yet when i place objects on the grid place where i want my artwork/text… update overlay ever thing looks aligned and good press START… and its always off … soo I make 3 circles top middle and bottom to ...

Darren

2023-12-25

130

1

0

A chiller is a cooling water equipment that can perform refrigeration, temperature control, and constant flow. It is widely used in various industrial and commercial fields. It is a device that absorbs heat and discharges it by circulating refrigerant. When using a chiller, there is a possibility of not cooling, so what is the reason for the chille...

Smith

2023-12-23

120

1

0

Hello… I am new to laser engraving/cutting. I purchased a TTS 10 Pro with a Dewalle air assist. I was able to connect everything. However, my Z axis has to be about 18mm above the wood to cut, which is not enough room to get my air assist underneath. Is there another way to mount the air assist so that it does not have to be underneath?

Abel

2023-12-23

158

1

0

I have used Lightburn for over a year and it continues to stop during jobs. This as cost a tremendous amount of lost time and materials. I’v tried everything. every post Iv read deals with windows operating systems. Im using a Mac with macOS Monterey version 12.3 can anyone help with this issue for a MAC? Im using a Ortho Laser Master 3 VIA U...

Aaron

2023-12-23

128

1

0

I’m a fairly new lightburn user. This is the first time i’m actually drawing in lightburn (as opposed to just importing images) I wanted to draw some text over a shape, but I quickly found that there’s no resize handles on the text. I have the curved arrows for rotate, but not the square handles for resizing. See the attached scre...

Marshall

2023-12-22

128

1

0