The Olive series picosecond ultraviolet laser adopts All-in-One integrated design, making the opto-mechanical structure more compact. The New electronic control system offers precise control and superior reliability. Utilizing Huaray independently developed and manufactured core seed source, it possesses long-term stability and reliability; with mu...

Christian

1 天前

18

0

0

Hello. Nesting does not work. I receive an undecipherable message "Г»ХTuSjУГb№". ) Software "VCutWorksSetup2.00.34-20250314". The computer is not connected to the machine, I need to work remotely, do cutting tasks.

7366BB9B

07-22

114

4

0

The Maple air-cooled nanosecond UV laser has enhanced cooling based on the previous generation of air-cooled lasers and can adapt to a wider environmental temperature range. It is small in size, easy to integrate, and suitable for high-frequency and stable marking on the assembly line.It has little thermal impact on the processing edge and is highl...

Nugent

07-24

70

0

0

Product DescriptionQ-switch series pulsed fiber laser is designed based on Q-switch oscillator and MOPA. The laser is transmitted by fiber and isolator, and is controlled through a 25-pin interface. The Q-switched pulse fiber laser is suitable for intergration, and could meet the requirements of plastic marking, metal marking, engraving, coating re...

Vasili

07-22

123

0

0

Hello, I'm upgrading an oscillating knife cutting machine. The machine had a Galileo controller. The PC used to operate it lost its hard drive. I couldn't configure the software from the backup I had.I purchased a Ruida RDD6616u controller from Wavetopsign on Aliexpress. I asked them for the installation manual and software on several occasions. I ...

Geozapata

06-14

296

7

0

Hi. I have a RDC6445G unit in my 130w CO2 laser. Normally in Lightburn I can choose a Tube Tpe of Glass, RF1, or RF2.Now I want to add a Diode Laser to my unit so I can do very fine detail work that the 130W cannot.My Ruida has 2 outputs, and depending on the mode it will either put out a 0-5v signal to drive the CO2 power supply.. or a PWM signal ...

7E026F24

07-20

105

1

0

Product Description1000W~6000W SINGLE MODULE CW FIBER LASER is a high-power fiber laser with high electro-optical conversion efficiency, compact size, good beam quality and maintenance-free. Wide fiber core diameter range from 100~600um, can be customized from 800um~1000um. Mainly used in metal welding and cladding and other fields such as new ener...

Payson

07-19

373

0

0

High-performance solid-state laserThe TruDisk is a high-power solid-state laser for the welding, cutting, and surface processing of metals. It impresses above all in situations which require the combination of high power and maximum beam quality. The new generation of TruDisk lasers provides you with great advantages, above all due to its much mor...

Terrelle

07-17

377

0

0

Product Features1. One laser, double the productivityWith up to two pluggable laser outputs, work can be carried out at one station while the other is being prepared. This avoids downtimes. Jobs can be carried out one after the other with full power or simultaneously with shared power.2. Low-spatter welding at maximum speedBrightLine Weld beam s...

Clarence

07-15

109

0

0

tengo una laser  H1610  la encendi y estaba en chino le cambie el lenguaje a ingles pero ya no estaba calibrada la calibre varias veces pero solo hace cut test cuando le doy star no corta hacia los lados ni hacia abajo y solo me corta en un pedazo y lo demas no corta 

500EA993

07-09

206

7

0

Main features：Long-term high reliabilityGood product consistencyApplication：Scientific ResearchCTPPerformance ParameterStructure Size (mm)

Nugent

07-10

149

0

0

dove trovo l'ordine dei layers in vcutworks

8CE9F5B6

07-09

195

1

0

There is support for ruida?I am using rdcutist 3.02.20 beta.I have the following problems:- Frame speed is very slow, can't change it.- If I connect parts and load them into RG6563FG. Cutting occurs with a visit (not always)- Focus, axis A can only be controlled in external coordinates. - IMPORTANT: In layer, membrane mode - does not turn on t...

Pavel_TT

2023-08-30

1K

25

5

HelloDoes anyone knows, will LightBurn works with Ruida RDC8445S ?I try trial version, and Ruida always in disconnected state, Serial USB/Ethernet IP both not works.PS: RDWorks detect controller by USB and IP (WiFi) - both success 

96DED7E9

05-15

600

4

0

GZTECH Nanosecond Pulsed Solid Green Laser Source is a compact, high-performance laser system designed for precision marking, micromachining, and scientific applications. It generates a stable, high-quality 532 nm green laser beam with nanosecond pulse duration, offering excellent beam quality (M² < 1.3) and high peak power for demanding industr...

Miller

07-08

326

0

0