The market share and usage rate of linear motors are increasing, partly due to the end users needing higher throughput and higher accuracy. The understanding of linear motors is usually that they can run at high speed, have long travel and high positioning accuracy, which other driving mechanisms cannot achieve. However, in fact, the advantages of ...

Jamie

2024-05-22

192

1

0

Hello,I did a rebuild of a Muse 2D and I got it working fine. In the past 2 weeks it started acting up during cuts. It will randomly reboot. It doesn't happen consistently like after a certain time, length, file size, settings, etc. It seems completely random. Doing a hard reboot with the switch doesn't resolve the issue. After a random number of r...

fCrtGR6q

2024-03-12

581

2

1

The laser control system is the control core of laser processing equipment. With its built-in high-performance processor, the laser control system can quickly calculate the processing path and allocate the power during processing in a reasonable way, allowing other equipment such as the laser, laser head, and motor to operate correctly and orderly,...

Roderick

2024-05-21

192

1

0

Laser marking is widely used, and through a highly concentrated laser beam, the laser machine can quickly evaporate and vaporize a part of the material surface, thereby forming identification patterns. Laser marking has advantages such as non deformation, wear resistance, high accuracy, and fast speed, and is widely used in various fields such as f...

RTP

2024-05-21

213

1

0

Common faults of variable frequency motors include:1. Inter turn short circuit and partial discharge: This is a common form of insulation type faults in variable frequency motors. Interturn short circuit is generally manifested as extensive damage to a coil in the motor, while partial discharge may occur when the motor coil looks good outside, but ...

55455rml

2024-05-21

200

1

0

What are the structural differences between synchronous motors and asynchronous motors?

Carey

2024-05-20

199

2

0

1.Firstly, check the main circuit. Whether the power supply is powered on, whether the voltage is normal, whether the starting overload fuse is burnt out, whether the air switch is tripped, whether the switch contact is intact, and whether the power supply is out of phase. When starting, observe the voltmeter and ammeter. When the industrial chille...

Andre J

2024-05-20

182

1

0

There are many reasons for random fracture of gear teeth, mainly including:1) Random fracture is usually caused by tooth defects, pitting, peeling, or other stress concentration sources forming excessively high local stress concentrations at that location.2) Under the action of alternating stress, defects such as inclusions and fine grinding crack...

이야기 너와

2024-05-20

193

1

0

Do you know the reason why the 57 stepper motor and synchronous belt on the X-axis, which was just adjusted in the past two days, lost its step again?At the beginning, the tensioning structure of the synchronous belt was adjusted to ensure that the tensioning force of the synchronous belt was strong enough, but there were still cases of slipping.

Tim Johnson

2024-05-16

206

2

0

The modulus pressure angle and helix angle determine the pitch of the base circle, and adding the number of teeth determines the size of the base circle. The size of the base circle determines the shape of the involute. To understand the definition of modulus, it is actually a parameter that is close to a coefficient and cannot be directly measured...

LWE

2024-05-16

157

1

0

It is inevitable to encounter malfunctions when using industrial chillers. Below are several common malfunctions and their causes during the use of chillersOil pressure alarm occurs during useCommon causes of oil pressure alarm in chillers:1. The internal parts of the chiller have not been inspected and cleaned, resulting in oil stains, oil pump f...

Ruddy

2024-05-16

196

1

0

Laser marking is currently one of the most widely used laser processing technologies. Its principle is to use a highly concentrated laser beam to instantly evaporate part of the material surface, forming an indelible mark. Laser marking has the advantages of fast speed, good texture, and high accuracy, and has been widely used in many industries su...

Durell

2024-05-15

197

2

0

Hi, I have the Rudia RDC6563FG-Lite and have some questions about the controller, It says it supports 5v and 24v output limit switches and there is a Limit polarity setting for positive and negative on software but changing this setting cause no change and limit is only triggered by GND connection. Am I doing something wrong or is PNP not supported...

Juan Barkhuizen

2024-05-14

223

1

0

During use, the performance of a chiller will gradually decrease over time. In fact, many faults have some precursors before they occur, which are commonly referred to as potential faults.The failure rate of a chiller also varies over time, which is commonly referred to as its lifespan.1. Phase 1: Early FailureEarly failures, also known as the br...

Hiroko

2024-05-15

194

1

0

Laser marking is currently one of the most widely used marking and processing methods. The patterns or text produced by laser marking have a good texture and are indelible. They are often used in packaging, advertising, cables, consumer electronics and other products. Laser marking can be applied in both large-scale factories and small workshops, b...

Andrej

2024-05-15

190

1

0