My setup consists of my workshop bench (fixed) with an array of 20mm dog holes MFT like. My main laser is a much upgraded S9 with a y-axis extension. Above the bench I have a wide angle LightBurn Camera. The laser is mounted via fixation devices that use the dog holes. After doing alignment I find that I can put the laser away and get it back to th...
2023-08-0422310Hi All,I am a few weeks into using the trial version of Lightburn with a Genmitsu 4040-Pro. I’ve had a great time with it to-date, until today.I have everything set on my trusty MacBook Pro. I prefer the Mac when designing and for general use. Today, I needed to get work done so I had the idea to set up Lightroom on a fairly new PC laptop. T...
2023-08-1137110everything worked fine for day one. then day 2 the x axis is now backwards where I use move function with the left arrow and moves in the negatives coordinates but it moves to the laser to the right on my 3d printer. at startup sometimes it will say hard limit triggered other times it will not and say homing ok. I wrote an email for support and did...
2023-08-0430610I recently purchased a k40 laser with the primary intent of engraving on wood pens that I make.I upgraded the control board to a Mini Gerbil 3 so that I can use Lightburn software. I have been around with the software and I kinda have the basics of engraving and cutting.Included in the K40 purchase was a chuck style rotary attachment. The guy didn...
2023-08-0425210Hi I need to set up my GeekCreit Sculpfun S9 for first time on Mac running Monterey with the LB version 1.4.01. I have not been able to do my first cut yet. When I’ve attempt to so far the machine is moving with the blue light on but nothing ever cuts into the 6mm eva foam I have setup. I’ve check all settings and can’t seem to fi...
2023-08-0430621Hello, I’m new here and new to laser engraving. I just bought the Atomstack A5 M40 and I’m getting a double/ghost image on the left side when engraving. I’ve adjusted the belts serval times, measured with a ruler and everything is even. Even uninstalled and reinstalled LightBurn and still getting the same outcome no matter what I ...
2023-08-0432810Hello, I am getting the following error “g-code words consist of a letter and a value. letter was not found.”, this is my first time trying to engrave an image. I have no idea what to change or do hahaI have a Atezr 35 diode laser, my computer is directly plugged into the laser, have pulled a couple of images to test and get the same e...
2023-08-2333410I have a design (or part of below). I want to engrave the square around the date without engraving the date (oh I hope that makes sense). So the finished engrave should have the date looking black (black anodised aluminium) another example below.Any help on how to achieve this in lightburn would be appreciated.
2023-08-2331010I have an engraving color difference between the center of my design and the ends. Do you know what is it for?
2023-08-2424710Greetings! Probably a Newbie question but I did a Boolean Union to create a new image (worked great!) and then I performed lots of more edits/changes on other parts of my project. Now I want to go back and undo the Boolean Union temporarily so I could re-use a part of the original image. Then I will re-do the Boolean Union. I think I have way to to...
2023-08-2327510Hello everyone I’m having a problem and I need help today I installed my atomstack a5 pro+ machine and started running I set the x axis to 410 y axis to 400 from the lightburn application.I set the origin point to the front left. Then, when I start the machine, when the machine goes to the corners and sides, there is an incredible noise and v...
2023-08-2228110Need help… I have a sculpfun s30 w10 Lazer and bought the camera attachment to it. I followed the set up video from sculpfun. I have a 400x400mm honeycomb but it is technically a bit smaller than a 400x400mm . I set up the distance of the camera at 350mm from the bed for the x axis. Centered the camera off cross hairs for the horizontal axis...
2023-08-2222110Does anybody know of a way to rotate a polygon (or any shape) by a specific number of degrees?I’m designing a shape for a gothic cinquefoil arch (I’m actually going to be turning this into a tutorial) - I’ve completed the steps but I need to fit an octagan into a circle, pointing upwards. When you master a polygon in LB it points...
2023-08-2130710Hello ,I use lightburn for quite some time , awesome piece of software.Although I like it and i use it very much , for the love of God and all the Angels in the heaven why is it so hard to put a lead in on the inside of a rectangle or other shapes. On circles is super easy , just put a negative angle , length and presto , inside lead in.On ...
2023-08-2136110have a k1 36 watt,power led bar registered full power when lightburn was set to 100%but now machine laser head output led bar is only showing 75-80 %
2023-08-2135810
- 暂无数据
简体中文
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski