When I use lightburn’s matrix option there is a risk when the engraver goes to work on the other duplicate design.If I send it to record individually, the problem doesn’t happen.Can someone help me, please?

Nugent

2023-08-11

359

1

0

Question regarding filled lines: when burning rectangles (and circles) Lightburn sends the laser side to side.This is great for the filled lines parallel to the laser travel (left and right) but not so good for vertical filled lines, it takes a lot of time for the verticals. It burns a tiny piece of one end, travels across and then burns a tiny pie...

Payson

2023-08-11

303

1

0

My setup consists of my workshop bench (fixed) with an array of 20mm dog holes MFT like. My main laser is a much upgraded S9 with a y-axis extension. Above the bench I have a wide angle LightBurn Camera. The laser is mounted via fixation devices that use the dog holes. After doing alignment I find that I can put the laser away and get it back to th...

Robert Evans

2023-08-04

232

1

0

Hi All,I am a few weeks into using the trial version of Lightburn with a Genmitsu 4040-Pro. I’ve had a great time with it to-date, until today.I have everything set on my trusty MacBook Pro. I prefer the Mac when designing and for general use. Today, I needed to get work done so I had the idea to set up Lightroom on a fairly new PC laptop. T...

Terrelle

2023-08-11

381

1

0

everything worked fine for day one. then day 2 the x axis is now backwards where I use move function with the left arrow and moves in the negatives coordinates but it moves to the laser to the right on my 3d printer. at startup sometimes it will say hard limit triggered other times it will not and say homing ok. I wrote an email for support and did...

John Trant

2023-08-04

313

1

0

I recently purchased a k40 laser with the primary intent of engraving on wood pens that I make.I upgraded the control board to a Mini Gerbil 3 so that I can use Lightburn software. I have been around with the software and I kinda have the basics of engraving and cutting.Included in the K40 purchase was a chuck style rotary attachment. The guy didn...

Liam

2023-08-04

262

1

0

Hi I need to set up my GeekCreit Sculpfun S9 for first time on Mac running Monterey with the LB version 1.4.01. I have not been able to do my first cut yet. When I’ve attempt to so far the machine is moving with the blue light on but nothing ever cuts into the 6mm eva foam I have setup. I’ve check all settings and can’t seem to fi...

Jen

2023-08-04

314

2

1

Hello, I’m new here and new to laser engraving. I just bought the Atomstack A5 M40 and I’m getting a double/ghost image on the left side when engraving. I’ve adjusted the belts serval times, measured with a ruler and everything is even. Even uninstalled and reinstalled LightBurn and still getting the same outcome no matter what I ...

roy

2023-08-04

337

1

0

Hello, I am getting the following error “g-code words consist of a letter and a value. letter was not found.”, this is my first time trying to engrave an image. I have no idea what to change or do hahaI have a Atezr 35 diode laser, my computer is directly plugged into the laser, have pulled a couple of images to test and get the same e...

Christian

2023-08-23

339

1

0

I have a design (or part of below). I want to engrave the square around the date without engraving the date (oh I hope that makes sense). So the finished engrave should have the date looking black (black anodised aluminium) another example below.Any help on how to achieve this in lightburn would be appreciated.

jessie

2023-08-23

319

1

0

I have an engraving color difference between the center of my design and the ends. Do you know what is it for?

Jamie

2023-08-24

256

1

0

Greetings! Probably a Newbie question but I did a Boolean Union to create a new image (worked great!) and then I performed lots of more edits/changes on other parts of my project. Now I want to go back and undo the Boolean Union temporarily so I could re-use a part of the original image. Then I will re-do the Boolean Union. I think I have way to to...

Nugent

2023-08-23

285

1

0

Hello everyone I’m having a problem and I need help today I installed my atomstack a5 pro+ machine and started running I set the x axis to 410 y axis to 400 from the lightburn application.I set the origin point to the front left. Then, when I start the machine, when the machine goes to the corners and sides, there is an incredible noise and v...

Miller

2023-08-22

289

1

0

Need help… I have a sculpfun s30 w10 Lazer and bought the camera attachment to it. I followed the set up video from sculpfun. I have a 400x400mm honeycomb but it is technically a bit smaller than a 400x400mm . I set up the distance of the camera at 350mm from the bed for the x axis. Centered the camera off cross hairs for the horizontal axis...

Darren

2023-08-22

226

1

0

Does anybody know of a way to rotate a polygon (or any shape) by a specific number of degrees?I’m designing a shape for a gothic cinquefoil arch (I’m actually going to be turning this into a tutorial) - I’ve completed the steps but I need to fit an octagan into a circle, pointing upwards. When you master a polygon in LB it points...

Tory

2023-08-21

311

1

0