Hi :slight_smile:I’m using LightBurn for a while now. There’s a problem I keep having where angled\curved sections of my designs are not cut through. Cuts would work perfectly in the x/y directions, but when the movement involves x&y motion at the same time, cutting does not work as well.See the attached images - paths at about 45 d...
2023-03-2017610Lead in/out does not show up in Workspace.in Preview i can see. How to see in Workspace?
2023-03-2034410I have a set of B2 servo in my hand. I would like to ask how to use B2 to control the motor for some simple movements, such as controlling the screw module from point A to point B (taking 10 seconds).
2023-03-2030210As the fundamental industry of China's economic development, the development of the machinery manufacturing industry is also further improving through continuous accumulation, and its current development is stable. There are various types of mechanical equipment, and their movement modes and functions are also different. Some mechanisms are relativ...
2023-03-2016400We got another Boss LS3655 delivered and setup went smoothly, belts are tight, lens is tight, mirrors are spot on, Bed is level, Head is 90^, alignment is perfect. We double checked everything. no issues. But, it’s printing squiggles on smaller font 1" size in light burn. these are Pre-loaded Fonts in lightburn, so no squiggle in the Original...
2023-03-1821610Hi can settings be changed and saved during the burn. I would like to change the number of passes on a particular layer that is being engraved. Or would I have to wait till current layer is done then start from the beginning again then go over itThanks
2023-03-1824910My laser just stopped working. I shut it off for the night and came back and it won’t fire.It runs the whole job with no laser.Any ideas on settings I should check? I set and reset focus several times.I have tried every combination of speed power to no avail.Any ideas?
2023-03-1821610I cut a cutting test card but when cutting the same material my machine does not cut through using the settings from the card. Any idea why?
2023-03-1820010Set the number of pulses per servo turn. When the lead screw stroke is 32mm, the servo setting is 3200 revolutions per turn, and the maximum output of the PLC is 100K. In this way, the maximum speed of the servo can only be 1850 revolutions. How can the maximum speed be 3000 revolutions?
2023-03-1725310I have the lose camera control issue all the time… kind of a pain to restart with shift to fix…but my other issue is many time when i open a new window it does not show up on a new tab … is there a way to fix this
2023-03-1821510I am installing lightburn on new laptop and got a couple questions.I am at the point where it found my device and is calling it GRBL, and it shows axis X=650mm & axis Y=500mm, and wants to know the dimensions of my working area is. The mm markings on the frame for X axis is 440, and Y axis is 520. On the Y axis there is a hard stop at 40 with l...
2023-03-1819010The closed-loop controlled frequency converter can achieve closed-loop position control in the stopped state through encoder detection, locking the servo motor shaft at a fixed angle. This function is called servo motor locking or zero servo function.
2023-03-1820210As a refrigeration device, the main components of an industrial water chiller include a compressor, evaporator, condenser, capillary throttle valve, etc., thereby achieving the refrigeration effect of the unit. In the actual use process, it is inevitable that some faults will occur in the cooling system of the water chiller, leading to the alarm of...
2023-03-1828200Laser water chiller is a water cooling device that can provide constant temperature, constant flow, and constant pressure cooling water. The working principle of a laser water chiller is to first inject a certain amount of water into the water tank inside the machine, cool the water through the cooling system of the water chiller, and then send the...
2023-03-1829000Hi, for a special project, I have to cut at 1000mm/sec but my machine refuse to go above what seems to be 500mm/sec. I went to the machine, modified the Idle Speed to 1000, the X axis max speed is at 1000mm/sec because I’m able to move at that speed but even if I input a cut speed of 1000, it runs lower that that.It’s not a matter of a...
2023-03-1726110
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski