How to control the stepper motor to realize intermittent feed motion by xinjie plc.

Nugent

2023-03-13

296

1

0

In the process of equipment debugging, it was found that the servo motor could not reach the specified position. After troubleshooting, it was found that there was a problem with the IO line of the driver. It would be good if it was replaced. The servo motor uses position control, and the command pulse sent by PLC will be lost due to the poor conta...

Marshall

2023-03-10

353

1

0

The servo motor moves intermittently and equidistantly. Assuming that the distance of each movement is 50mm, the calculated pulse is with a decimal point, which will cause cumulative error. Is there any solution?

Nugent

2023-03-07

358

1

0

Master, why do some encoders of servo motors need to be zeroed when they are removed or replaced. What kind of encoder should be zeroed and what kind of encoder should not be adjusted.

Williams

2023-03-06

350

1

0

Now many motor factories have begun to use motor assembly lines to produce motors, which not only greatly improves the efficiency and saves a lot of labor costs, but also is better than manual assembly. It is quite convenient to match a good detection system. So what are the principles for the layout of motor assembly lines as a manufacturer of mot...

Abel

2023-03-06

195

0

0

The servo motor moves up and down, has an origin, and moves up and down in the process of returning to zero. Each time, the value of moving up and in place is periodic, pulse signal, what is the situation.

Patrick

2023-03-04

323

1

0

In servo torque mode, the speed limit value is controlled by analog quantity, and the torque limit signal is used to achieve the purpose of screwing.At present, the problem is: when the torque limit signal is output, you want to judge whether it is screwed in place. How do you realize this working condition? What is the convenient way?In addition, ...

jessie

2023-03-04

270

1

0

Which control mode is generally used for servo press?

Williams

2023-03-03

252

1

0

Siemens servo homing failed. I am the disc homing. After I turn back, the zero position and the last homing position cannot coincide. The known reduction ratio is 1:20. Please tell me how to deal with it.

Abel

2023-03-03

144

1

0

For example, Siemens SMART PLC, SMART LINE screen, for example, the motor starts at the set time, stops at noon and evening rest time, and the rest time (settable) automatically starts and runs.

Aaron

2023-03-03

312

1

0

How to select a suitable linear motor module to maintain the stability and efficiency of the equipment.Linear motor selection elements:1. The movement load, the maximum load that can be borne (the safety margin is 80%), and the movement center of gravity deviation.2. Linear motor installation mode: horizontal installation is the best way under the...

Clarence

2023-03-02

329

0

0

Done a new build with Annoy tools Board double Y axis (newish to game) The build is A1 all brand new The X Axis just makes a little noise doesn’t do anything all the cables are okay and swapped motors around all A1 Any help…

Kevin

2023-02-23

204

1

0

The Z stepper on my 4X8' machine is going bad. I want to upgrade all of the steppers to servos but that's a big cost and I'd like to get back up and running quickly. Is it a problem to replace just the bad Z stepper with a ClearPath Servo and related power accessories to drive it? I'm already getting ready to make the switch from Mach3 to Mach4 and...

Tory

2023-02-21

326

5

0

I have a Bridgeport V2XT currently 3 hp intermittent and 2 hp continuous spindle. Got it running on a Mitsubishi FR-720S-100 VFD. Interested in replacing that spindle motor with a 3.7 KW and then having to change the VFD to a bigger Yaskawa so can continue running on single phase or maybe I just keep it 2.2Kw and enjoy the greater speed range? That...

Simon

2023-02-21

303

1

0

I'm starting to spec out a new bench top machine build that I'm hoping to put together for some small scale project work in various different materials, though probably with a focus on aluminium plate. Realistically I'm probably looking at the more budget friendly spindles and VFDs available on AliExpress to get this moving so budget is something I...

Aaron

2023-02-21

169

1

0