Text misaligned using rotary roller
12 hours ago200When I finished recording the topic, the measurement values in millimeters did not match.For example, I entered a value and assumed it was 5mm x 5mm and carved as 8mm x 8mm. I don't know how to fix the code so that the measured value I entered is exactly the same as the value I want to cut or carve. I appreciate any help you have provided.
01-17126301. Choose high-quality optical componentsImportance: The accuracy and durability of optical components directly affect the transmission and focusing effect of laser beams.Measures: Select optical components with high precision, low loss, and good stability, such as lenses, mirrors, etc. These components should be able to maintain long-term stable p...
15 hours ago400If you at the TWhat causes the arrow tips in the corners of the T all other fonts have it also except the OThis an Arial font which has been switched from a Sans Sherif font which did the same thing.From what I can see I have nothing extra switched onThe strange thing is if I increase the power the arrows go away which doesn’t work in this case. Th...
02-172840Is my Ortur Laser Master 2 Pro XY out of calibration? Is there a way to calibrate mechanically or thru Lightburn SW? It is a fairly new system and not used to much. Circles and repeatability after a pause likely in the Y axis is off.
02-144150I have a longer Ray5 10watt, first laser and have had about 5 mths now. I upgraded to a enclosure, limit switches, air pump and camera. Everything is mostly good except the 5 mp camera from longer. It’s from longer and is set at the correct height. The average offset is around 1 1/2mm to 2 1/2mm depend on where it’s at on the work are. Over all it ...
4 days ago2630I have an Algolaser DIY 20W and everything works normally. Recently, I bought a Delta 22W, and when performing the material test, I have this misalignment problem.I have already tried tightening the belts and checking for vibrations, but nothing, absolutely nothing works.Does anyone have any ideas on how to solve this?
2 days ago1110Fault in the fiber optic section1. Fiber breakage: Fiber breakage is the most common situation in fiber laser machine failures, usually occurring in fibers that have been in use for a long time or have been excessively bent. The solution is to replace the fiber with a new one.2. Fiber optic pollution: When the surface of the fiber optic cable is co...
2 days ago700I’m trying to engrave the base of multiple trays at once.Since the sides of the trays are higher than the laser’s focus distance, the laser head bumps into them when moving from one tray (or group of trays) to another.I figured that I could use multiple layers and insert a dummy layer in between to reset the laser head to a safe height.Is there a ...
02-134160Pavel, I have the same problem as you. I connected the RUIDA 6563f controller to the MAX MFSC 1500X laser, but I can't turn on the laser from the panel. Do you have an idea! Kind regards, M.
3 days ago2410Dear Sir,We have an RDC6445S working in a LaserSaur machine, the cutting file come from RDWorks through USB cable.If we place a speed of 100 mm/s in RDworks, the file receive by RDC6445S shows on the screen a speed of 100 mm/s, but the working speed is only 100/5 = 20 mm/s.At the same time, if we tranfer laser head at a 100 mm/s speed (visible o...
2 days ago2210Hello! I’m new to the world of laser engraving and cutting, I have a Sculpfun S9 laser, I use Illustrator for my designs, I was making some keychains but when the shape is very complex the vector imports so badly, it gets deformed. I noticed that it does this if the vector had a lot of points, I tried to clean it up but now I see that some shapes a...
3 days ago1310Laser cladding generally uses materials such as iron-based alloys, nickel based alloys, titanium alloys, Al Si alloys, stainless steel, etc.The materials for laser cladding are mainly metallic materials, including iron-based alloys, nickel based alloys, titanium alloys, Al Si alloys, stainless steel, and so on. These materials have good melting p...
3 days ago1100When repairing the grounding fault of the armature winding of a DC motor, we can use various techniques. Firstly, it is necessary to ensure the use of convenient and practical maintenance tools, such as armature maintenance lights. Connect the lamp to the circuit and clarify the fault situation through the operation method. If the light is on after...
4 days ago1200Everything works great except lightburn is not tracking, in the program, my laser’s movement. The laser is burning, it works fine. But as you can see on the attached image, the upper green and red squares? Those never move.Any advice is appreciated, I searched but didn’t find anything that helped, maybe just a link in the right direction? Appreciat...
02-153240
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski