English
  • The servo motor moves intermittently and equidistantly. Assuming that the distance of each movement is 50mm, the calculated pulse is with a decimal point, which will cause cumulative error. Is there any solution?

    2023-03-07
    355
    1
    0
  • I have two problems:First…My software doesn’t allow me to choose what type of image to print. eg. Newsprint, gray scale. It just picks one at random. Second…the pause button doesn’t have any effect on my machine. OLM3. I’m running win11 64bit. Thank you.

    2023-03-07
    284
    1
    0
  • In industrial applications, we often use laser ranging sensors because they can accurately estimate the distance to the target through very weak optical signals. In addition, it can record and process the time from the light pulse sending to receiving back, so as to measure the target. So, what problems should we pay attention to when using laser d...

    2023-03-07
    285
    0
    0
  • Working principle of laser water chillerA certain amount of water is injected into the case, and then the water is cooled by the cooling system of the water chiller. The cooling water is circulated to the laser equipment through the water pump, and the cooling purpose is achieved by reciprocating circulation.Advantages of laser chiller1. Th...

    2023-03-07
    316
    0
    0
  • As the third generation photovoltaic cell technology, perovskite cells have strong theoretical advantages compared with crystalline silicon and thin film cells due to their material characteristics. The theoretical efficiency is higher, and the theoretical efficiency limit of single-junction perovskite battery can reach 33%, which is higher than th...

    2023-03-07
    282
    0
    0
  • Hi,I am about to finalize my order of CF-30 which has a “cloudray integrated control card” and also a “BJJCZ Control board”.The later, I assume to be working fine with Lightburn (with galvo license), correct?The CF-30 is delivered with a touchscreen control panel, which runs with a self-developed software by CloudRay. Can...

    2023-03-06
    199
    1
    0
  • I have been trying to find out if there is a way to turn down the power supply to match my tube. I did a ramp test and my tube is rated to max out at 26ma but the controller is only at 70%. I want to make 26ma 100% so no one over drivers the tube. Is this possible?

    2023-03-06
    262
    1
    0
  • Hey, it’s my first time using lightburn and was wondering where would be best forum to get my cutting images from. I have found some images on shuttlestock that i would like to laser round but is there a better place I can go so I don’t have to sign up with a subscription? I am wanting a horse silhouette to laser around.

    2023-03-06
    256
    1
    0
  • I just got my sculpfun s9 setup with lightburn. Dont understand why it is printing mirrored to the Y Axis. Change Device Setting Origin, using the 4 options, computer screen follows the setting but its always mirror on the Y Axis. I need help please.

    2023-03-06
    338
    1
    0
  • Downloaded a SVG file fro Etsy.Transfered the file to Lightburn but the image just blinks on and off when selected.Why?

    2023-03-06
    366
    1
    0
  • Master, why do some encoders of servo motors need to be zeroed when they are removed or replaced. What kind of encoder should be zeroed and what kind of encoder should not be adjusted.

    2023-03-06
    347
    1
    0
  • Now many motor factories have begun to use motor assembly lines to produce motors, which not only greatly improves the efficiency and saves a lot of labor costs, but also is better than manual assembly. It is quite convenient to match a good detection system. So what are the principles for the layout of motor assembly lines as a manufacturer of mot...

    2023-03-06
    192
    0
    0
  • High-speed laser cladding is a fast laser surface treatment technology. Its process characteristics are good cladding quality, high speed, low cost, and certain market competitive advantages. Improper selection of process parameters for high-speed laser cladding will lead to poor forming quality and easy deformation.The key parameters invol...

    2023-03-06
    296
    0
    0
  • I had similart probblem before. There must be a setting enabled addlling this kerf and I donmty know where to disable it. As you see in pics I’ve uploaded itrs adding an offset or kerf again . Can you tell me where to turn this off and how I remove it now with this project.

    2023-03-04
    344
    1
    0
  • Hi friends! Please see attached pic, there is a visible jittering while the laser head changes direction from the vertical to horizontal movement, immediately after the turn, everything ok on slow speed but appears on medium and high, any suggestions how to fix it please? ThanksPS: could it be because of the table with the laser slightly unstable...

    2023-03-04
    255
    1
    0