When choosing a laser cleaning machine, to ensure the selection of suitable equipment, users need to pay attention to and confirm the following key parameters:1、 Laser powerLaser power is an important factor affecting the cleaning effect and speed. Generally speaking, the higher the power, the better the cleaning effect and the faster the speed. ...

Christian

2024-12-10

199

0

0

Handheld laser welding machines, as an important tool in modern welding technology, have been widely used in various industries due to their high efficiency, precision, and flexibility. However, correct operating techniques and safety precautions are key to ensuring welding quality and operator safety. This article will provide a detailed introduct...

Smith

2024-12-09

96

0

0

Recently, when I try to engrave using my Xtool D1 pro, the engraving is way off. When I frame the job, everything looks fine. But once I start to engrave, the laser moves roughly 1.5 inches to the left. This has happened consistently over the last month. I’ve managed the engraving by manually adjusting the starting point of the laser.Today, I trie...

Tim Johnson

2024-12-06

75

2

0

The laser stops firing in the meddle of the job but the head doesn’t stops. When that happens, the head eventually stops, moves back and tries to keep engraving where it stops. The problem with that is that when that happens it never restart in the same position, making a really noticeable line along the path. That line is just shifted from the “or...

Jack Wilborn

2024-12-07

111

1

0

Introduction to Laser CladdingLaser cladding is a process of partially melting the surface of a material by irradiating it with a laser beam, spraying powder or wire onto the melted surface to generate a new surface layer. It can be used to repair damaged components, improve surface hardness, enhance surface performance, etc.Factors affecting the...

Vasili

2024-12-06

80

0

0

Hello,I also have the problem that when transferring data I get the error message that an error occurred while sending (the device may be busy or stopped).In the forum I found a post that you can try to set "enable DTR signal" in the device settings.Where exactly can I select this in the device settings?

JOST

2024-12-05

70

1

0

Power failure1. Check if the power cord is securely plugged in;2. Check if the power cord is damaged;3. Check if the power supply is working properly.Laser malfunction1. Check if the laser is working properly;2. Check if the laser cable is securely plugged in;3. Check if the laser cable is damaged.Other reasons1. Check if the light tube has expi...

Clarence

2024-12-04

68

0

0

Multiple methods can be used to avoid the problem of laser welding undercutting, such as optimizing process parameters, reducing welding speed, optimizing plate edges, etc.Reasons for laser welding edge biting problemThe problem of laser welding undercutting refers to the phenomenon of excessive melting and compression at the welding point during ...

Smith

2024-12-02

89

2

0

Problem OverviewThe inability of laser cladding powder to hang refers to the phenomenon where the powder cannot uniformly adhere to the substrate during the laser scanning process, resulting in phenomena such as powder falling off. This phenomenon not only affects the processing effect, but may also damage the equipment.Root cause analysis of the...

Cyril

2024-12-03

118

1

0

Parameter adjustment skillsIt is very important to set and adjust parameters correctly when performing handheld laser welding. Here are some parameter adjustment techniques:1. PowerHandheld laser welding machines are usually equipped with adjustable focal lengths. During the welding process, the focal length can be adjusted according to the condi...

Darren

2024-12-03

91

0

0

With the rapid development of laser cleaning technology, it has gradually entered people's lives due to its unique advantages such as low damage to the substrate material, high cleaning accuracy, zero emissions, and no pollution. There is no doubt that applying laser cleaning technology to the cleaning of dirt on metal surfaces has a very broad pro...

Kevin

2024-11-29

104

2

1

UV laser is a special type of laser with a short wavelength, concentrated energy, and short pulse frequency. The wavelength range of this laser is between 200~400nm, and its high-energy photons can break chemical bonds on materials at the molecular level, thereby achieving the effect of separating and breaking materials. These characteristics make ...

Williams

2024-12-02

96

0

0

1. Self melting alloy powdercharacteristic:Containing B and Si (functions: deoxidation, slagging).Substrate adaptability.It can be widely used in various materials including carbon steel, alloy steel, stainless steel, and cast iron, but it is not suitable for steel with high sulfur content because the sulfur in the steel will form a low melting poi...

Aaron

2024-11-29

94

0

0

I have an S1 and am currently using Lightburn 7.03. In previous forums, there was lengthy discussions about this issue and last May, it was posted that the new Lightburn version 7.0 would fix it. I cam using the current version, and my S1 is still cutting triangles when I put a square around a design to be cut. It finishes cutting the design and th...

Silvano

2024-11-21

134

5

0

To improve the efficiency and stability of laser welding, the following aspects can be considered and operated:1、 Equipment selection and optimizationChoosing high-power lasers: Higher power output can significantly accelerate welding speed, thereby improving overall efficiency.Equipped with advanced optical systems: can effectively ensure beam qu...

Darren

2024-11-27

92

1

0