it doesnt matter what i try I can draw a circle and then a square and the weld command may or may not highlight… booleon never does. it just started in current version

Erdogan

2024-11-15

116

1

0

I have an Atomstack A70 with a movable z axis, the issue is that when I home the machine the z axis does not move up. I can move it with the move buttons and with a z home macro $HZ. The x and y axis home as they should. Thanks.

55455rml

2024-11-08

97

5

0

Just curious how the folks here have found using certain places on the X/Y table for placement of the work material ?I noticed, and makes sense, alot of folks use the back left corner to set up a square for dropping in material or maybe a work jig to engrave or cut.This makes sense as this is the best point for the mirror distant and it should fol...

Silvano

2024-11-11

81

3

0

I discovered after scanning some letters that the “insides” of some letters (think the “bowls” in capital B) were separate from the “outside” of the letters. I know I can Group the two objects (inside and outside) but the grouping can easily (for me) be undone accidentally. It appears that the only way of permanently joining them is to Weld them. H...

Narrator

2024-11-13

100

1

0

Hi all, I’ve been running Lightburn on an Ortur LM3 for about a month now, and a new issue has developed.I’m running a batch of bookmarks with this program, and it starts up fine, frames my object in workspace center, and runs the program in workspace center. But then…IF I PRESS START AGAIN: It repeats the program, but about 30mm to the left.IF I F...

berainlb

2024-11-13

116

1

0

So I have a Creality Ender 3 S1 Plus with 5W laser module set up. It has not been cutting at its full power, because it cut the same material at the same speeds in Creality Print. So I found out that the S-Value Max setting needs to be set to your machine. My problem is I don’t know what setting to set it to. I’m including a picture of my machine s...

James

2024-11-12

130

1

0

I purchased a new laser and computer and downloaded light burn onto the new computer…which is an updated version compared to what I have been using. I check all my settings to make sure they match my other computers/lasers as the new laser is the same as another one I use. When I go to use it, it frames fine but when I try to engrave the laser head...

Roderick

2024-11-11

139

1

0

Na het instaleren van de limitswitches wat ook de nodige problemen gaf eindelijk alles good 0 postie wordt gevonden. framen laser aan met framen. eerder kreeg een continu straal die rond het werkstuk ging en de frame aangaf van af nu knippert hij, daarnaast graveert hij dus ook niet meer snijden gaat wel goed wie weet raad

이야기 너와

2024-11-09

80

1

0

All about remembering z height.when starting a cut.I’ve set my origin and home fine on the machine itself and with tests and using luban I am able to move from origin to home and back lazer something and repeat.However when using lightburn the first item placed does ok, it seems to remember the origin and home points from the machine, but for any...

Andre J

2024-11-07

102

2

0

Hi. I am attempting to use a workflow that generates the following svg i need to import into lightburn. When I import it, the font reverts to Ariel. If I ungroup everything, I can change the font but that is a big time waste. I could also export as paths, but I would prefer to maintain the ability to edit the text. Is there a way to address this? T...

Jack Wilborn

2024-11-07

134

2

0

Hi, can you please advise. Is there any way to ensure that the beginning (3-5 mm) is also cut through when cutting the poplar plywood? I can increase the power or decrease the speed, but then the rest will be pretty burnt. A ramp like a cnc milling machine would be good. Thanks.

Farouk

2024-11-06

99

3

0

Machine: Raycus 30w Fiber laserComputer: WindowsMy Raycus fiber laser stopped working. Actually, I do not think it ever worked correctly. I was never able to engrave metal with it.I have been using it to engrave water bottles for a few months. I noticed that the engraving was getting lighter (not removing all the paint) after an hour or so of use...

Andrej

2024-11-08

84

1

0

On white bath panel mdf but as image this time.sculpfun s9 2000 mm at 75% using jarvis setting and air assist with good ventilation.Edited in gimp and inkscape to remove speckle and firm up lines.

Ethan

2024-11-05

131

2

0

Hi everyone - I’m a newbie to the engraving world and got everything up & running with my Creality Falcon 22W laser + Rotary Pro. I’ve watched all the YouTube videos for full wrap tumblers, messed with all the settings and after trying different things for hours and scouring the internet for my specific issue… I’m still at a loss.The laser is ...

berainlb

2024-11-04

124

3

0

So I just replaced the tube in my machine and got a wattage tester to confirm its output. After a lot of careful testing, I’m finding that it is maxing out at 110ish watts on a 130 watt tube. Because of this, I’m hoping to find a way to do a system wide power scale so that if for a part I need as much power as I can get, I can put it 100% into the ...

Rajiv001

2024-11-06

100

1

0