As the third generation photovoltaic cell technology, perovskite cells have strong theoretical advantages compared with crystalline silicon and thin film cells due to their material characteristics. The theoretical efficiency is higher, and the theoretical efficiency limit of single-junction perovskite battery can reach 33%, which is higher than th...
2023-03-0732100Hi,I am about to finalize my order of CF-30 which has a “cloudray integrated control card” and also a “BJJCZ Control board”.The later, I assume to be working fine with Lightburn (with galvo license), correct?The CF-30 is delivered with a touchscreen control panel, which runs with a self-developed software by CloudRay. Can...
2023-03-0625110I have been trying to find out if there is a way to turn down the power supply to match my tube. I did a ramp test and my tube is rated to max out at 26ma but the controller is only at 70%. I want to make 26ma 100% so no one over drivers the tube. Is this possible?
2023-03-0630810Hey, it’s my first time using lightburn and was wondering where would be best forum to get my cutting images from. I have found some images on shuttlestock that i would like to laser round but is there a better place I can go so I don’t have to sign up with a subscription? I am wanting a horse silhouette to laser around.
2023-03-0630610I just got my sculpfun s9 setup with lightburn. Dont understand why it is printing mirrored to the Y Axis. Change Device Setting Origin, using the 4 options, computer screen follows the setting but its always mirror on the Y Axis. I need help please.
2023-03-0638310Downloaded a SVG file fro Etsy.Transfered the file to Lightburn but the image just blinks on and off when selected.Why?
2023-03-0640110Master, why do some encoders of servo motors need to be zeroed when they are removed or replaced. What kind of encoder should be zeroed and what kind of encoder should not be adjusted.
2023-03-0638810Now many motor factories have begun to use motor assembly lines to produce motors, which not only greatly improves the efficiency and saves a lot of labor costs, but also is better than manual assembly. It is quite convenient to match a good detection system. So what are the principles for the layout of motor assembly lines as a manufacturer of mot...
2023-03-0625500High-speed laser cladding is a fast laser surface treatment technology. Its process characteristics are good cladding quality, high speed, low cost, and certain market competitive advantages. Improper selection of process parameters for high-speed laser cladding will lead to poor forming quality and easy deformation.The key parameters invol...
2023-03-0632900I had similart probblem before. There must be a setting enabled addlling this kerf and I donmty know where to disable it. As you see in pics I’ve uploaded itrs adding an offset or kerf again . Can you tell me where to turn this off and how I remove it now with this project.
2023-03-0439210Hi friends! Please see attached pic, there is a visible jittering while the laser head changes direction from the vertical to horizontal movement, immediately after the turn, everything ok on slow speed but appears on medium and high, any suggestions how to fix it please? ThanksPS: could it be because of the table with the laser slightly unstable...
2023-03-0430610with lightburn active, and Ortur Master 3 on, I send a cut path to the laser, this is what i get “Trouble sending data to laser, Machine maybe busy or paused” I’m just getting started. Needhelp.
2023-03-0421210I’ve gone through the process in full from the official installation page, and it’s still not working.That was an attempt at the .run file, terminal looks like it went, but nothing to actually start it from.I then navigate to the folder it’s referencing, set it to be trusted, icon shows, but nothing happens when I double click it...
2023-03-04271103D simulation of how the wake behind the electron beam (purple) and the light pulse (blue and red stripes) surf behind it. The plasma wake shows no electrons in alternating yellow, and green shows the peak of electron density. When the light pulse is located on the boundary, it can continuously obtain energy - the trick is to keep it there. Source:...
2023-03-0420210The servo motor is used with the reducer, such as the planetary reducer. The reducer has a reduction ratio. The servo motor outputs the specified speed. After the reducer decelerates and increases the torque, will the speed accuracy of the output shaft of the reducer be improved? Or does the reducer affect the speed accuracy of the servo motor? Is ...
2023-03-0436610
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski