Laser cutting technology is widely used in various industrial manufacturing fields due to its high precision and efficiency. However, in order to ensure cutting quality and equipment lifespan, it is necessary to strictly control the operating environment. The following are the key environmental conditions required for laser cutting:1、 Suitable te...
01-0212524Reasons for deformation of acrylic sheet during laser cuttingAcrylic sheet is a commonly used organic glass, which is widely used in industries such as advertising signs, lighting fixtures, furniture, etc. When laser cutting acrylic sheets, deformation may occur. There are various reasons for the deformation of acrylic sheets: it may be due to exce...
2024-12-3017623The principle of laser cutting tempered glassLaser cutting is a technology that uses a laser beam to perform thermal processing on materials. Under the irradiation of a laser beam, the surface of tempered glass undergoes instantaneous thermal expansion and cooling, resulting in a stress difference that causes the glass to fracture in the laser beam...
2024-12-31149221、 Waterway inspectionThe main reason for abnormal water flow in the laser is due to water blockage or pump failure. Therefore, we first need to check whether the water path of the laser is blocked and whether it is well connected. If there is a blockage in the waterway, it is necessary to clean or replace the local water pipe and exhaust it. If th...
01-069501So. I’ve always cut stars with my Ortur Laser Master pro at a speed of 80 and 80 power. Always worked like a charm. Now it’s not cutting thru the basswood. You see a faint line on the backside and that’s it. This is extremely frustrating. Any help would be great.
2024-12-2012030Hi, I have an omtech 80w laser that I’ve had for about 6 months. I’ve been using it a lot more often in the past 2 weeks gearing up for the holidays. I mostly just am curious about maintenance. My machine has suddenly stopped cutting as well: I’ve taken the nozzle apart and cleaned the lens. I’ve cleaned the mirrors as well. Maybe I’m not doing goo...
2024-12-1814040To avoid producing burnt or yellow edges when cutting acrylic sheets, the following methods can be adopted:1. Using high-power laser cutting machines: High power laser cutting machines can quickly and accurately complete cutting tasks, reducing the possibility of producing focal edges during cutting.2. Adjusting the parameters of the laser cutti...
2024-12-2012200Power failure1. Check if the power cord is securely plugged in;2. Check if the power cord is damaged;3. Check if the power supply is working properly.Laser malfunction1. Check if the laser is working properly;2. Check if the laser cable is securely plugged in;3. Check if the laser cable is damaged.Other reasons1. Check if the light tube has expi...
2024-12-046400I have an S1 and am currently using Lightburn 7.03. In previous forums, there was lengthy discussions about this issue and last May, it was posted that the new Lightburn version 7.0 would fix it. I cam using the current version, and my S1 is still cutting triangles when I put a square around a design to be cut. It finishes cutting the design and th...
2024-11-2113250Any of you out there consistently cut half-inch acrylic? I did it once by trial and error and because my settings were wrong, I actually damaged my edges a little bit. I only have one piece to get one shot at this.I have access to a shared machine, which is 100 W. We have a 4 inch cutting head In which I don’t have that much experience with.Can you...
2024-11-1511020Just curious how the folks here have found using certain places on the X/Y table for placement of the work material ?I noticed, and makes sense, alot of folks use the back left corner to set up a square for dropping in material or maybe a work jig to engrave or cut.This makes sense as this is the best point for the mirror distant and it should fol...
2024-11-117830So I have a Creality Ender 3 S1 Plus with 5W laser module set up. It has not been cutting at its full power, because it cut the same material at the same speeds in Creality Print. So I found out that the S-Value Max setting needs to be set to your machine. My problem is I don’t know what setting to set it to. I’m including a picture of my machine s...
2024-11-1212410Na het instaleren van de limitswitches wat ook de nodige problemen gaf eindelijk alles good 0 postie wordt gevonden. framen laser aan met framen. eerder kreeg een continu straal die rond het werkstuk ging en de frame aangaf van af nu knippert hij, daarnaast graveert hij dus ook niet meer snijden gaat wel goed wie weet raad
2024-11-098010Hi, can you please advise. Is there any way to ensure that the beginning (3-5 mm) is also cut through when cutting the poplar plywood? I can increase the power or decrease the speed, but then the rest will be pretty burnt. A ramp like a cnc milling machine would be good. Thanks.
2024-11-069530So I just replaced the tube in my machine and got a wattage tester to confirm its output. After a lot of careful testing, I’m finding that it is maxing out at 110ish watts on a 130 watt tube. Because of this, I’m hoping to find a way to do a system wide power scale so that if for a part I need as much power as I can get, I can put it 100% into the ...
2024-11-069610
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski