There is support for ruida?I am using rdcutist 3.02.20 beta.I have the following problems:- Frame speed is very slow, can't change it.- If I connect parts and load them into RG6563FG. Cutting occurs with a visit (not always)- Focus, axis A can only be controlled in external coordinates. - IMPORTANT: In layer, membrane mode - does not turn on t...

Pavel_TT

2023-08-30

486

23

4

Hi,My machine has a rdc6563f controller an i use rdcutist 3I have worked out most issues but i cannot find how to continiue a cut after a collision.If i have a part stand up and the laser head touchs it , the machine stops and an alarm is then on the screen(collision).It asks to press esc to clear.I clear the alarm and when I then press st...

ROD

2023-11-02

131

2

0

Hi everyone!Please help with RDC6563FG controllerHeught senson has no effect in HMI panel, if i chorted nozzle to earth, i dont see the alarm in controllerI bought a new one aplifier, and this sensor dont worked tooAnd axis Z has not moving any way, i checked up to PIN8(DA) in Z axis motor interface, and i have only 0v in this pin. Any ideas how a ...

hqEbIakv

2023-10-19

184

1

0

Hello everyone, I want to use the RDC6445G controller for the first time and I have some doubts:1- is it not necessary to reset the axes?2- Are the inputs on the CN3-CN4 connectors related to the hardware limit switches?3- where can I find all the documentation?4- Are the outputs on the CN1 connector programmable?Thanks in advance

Cruise Wang

2023-04-18

263

2

0

Hello!I can't adjust the gas pressure regulator.in the setting, the slok costs 1MPa. ITV2030 shows 0.75MPa.Can you tell me how to do the same?

Pavel_TT

2023-07-10

360

5

0

HiI have read the manual of RDC6563F and RDC6563FG-LITE (in Chinese). I understand the difference between these models. I don't know how to connect the BM111 cutting head with AutoFocus. Can you help me? Which axis of the RDC6563 controller controls the AutoFocus function of this head and how to change it in the RDCutist 3.02.20 software. Can the ...

Robertulus

2023-09-18

142

3

1

Hi,I would like to ask you to explain the difference between these models.

Robertulus

2023-09-15

320

1

0

Hello everyone, I wanted to see if the ruida rd6445g-dfm-rd could be replaced by the ruida rd6445s ??.since the rd6445g had a problem and cannot be used

elsesser

2023-09-02

253

9

0

First off, don't leave your machine alone running in an enclosed cabinet for an hour (tried to make a power scale on EPDM rubber).Now, does anyone know where I can find a manufactured Ruida controlled machine that with an 80W diode under $2,000.00?

Dan

2023-09-05

303

4

0

Has anyone encountered this problem and how did they solve it?

Leon

2023-08-28

186

1

0

I have a laser with the RDC6442G controller that is less than a year old. Everything has worked fine until a week ago when the left arrow would move the gantry to the left and backwards at the same time. The back arrow also moves it back and to the left at the same time. Right and front arrows work correctly. The Z/U button also occasionally moves ...

Zfr6TL31

2023-06-27

301

1

0

Hi all,I've just completed building a 600mm x 400mm 90w machine with an RDC6445G controller.I noticed (in the manual) that a tri-color warning lamp can be connected to the controller but I'm unsure how to do this. I did see a video on YouTube where a single lamp was connected to the 'Status' pin but I would like a three-color lamp (...

Keith23

2023-06-07

177

1

0

Hi, I have been trying to engrave the Text on wood using milling cutter, however when I import the file from Illustrator to Vcut works it changes the image and cuts only boarder lines as a cut out.How can i engrave the entire world instead of making it a cut out. Can any one guide ?Regards

Hussain Raza

2023-06-05

332

1

0

The cutting drawing is not closed, and there is no problem with the drawing. How to solve this problem?

Jen

2023-01-09

267

2

0

I am looking for help with my Ruida 6445G Controller. The problem is the Z Axis. I have tried multiple options. Trying to get the Z Axis to show me in mm the actual length is not happening. For 100mm on the Controller is only about 4mm movement. I tried using the Auto calculations of Entering this information and the stepper was set at 0.2 which th...

DJPeterLewis

2023-01-30

256

11

2