Got my Polar 350 OMTech laser in February. I followed all the instructions I could find very slowly and carefully and it has worked perfectly and still does. My camera was the hardest but I got it very close to perfect. It was working until today when the area covered came up as a square in Lightburn instead of the bed size? The picture shows on th...
2023-05-0519220I am attempting to create an image that has a filled in area, with unfilled circles. I attempted to use “line” on the circles, but it doesn’t recognize them and fills the areas in anyways. Suggestions?
2023-05-0529810When I import a .png file it looks fine in the software. But when engraving, the bottom of the image is a little compressed. It helps to put a point under it, so the design is not the lowest point, but isn’t there a better solution?
2023-05-0510510I am attempting to use variable text with a csv file. I have a 3 x 3 array to fill with names from one column. I have advance by set to 1. The software is stuck on the first cell of the excel and isn’t advancing to the next name so my 3 x 3 array has the same name for all 9. Any assistance welcomed.
2023-05-0515610I have an xtool D1 Pro 20W and am new to lightburn. I had used it several times without problems but I just did the recent update and when I went back into lightburn I t is having problems with the connection. It only gives me (bluetooth-incoming port) to select nothing else. I went into my computer and turned off bluetooth to see what would happen...
2023-05-0519210A wide-tuned (2.47-2.64 micron) hybrid Laser based on a GaSb/GaInAsSb quantum well and a LIGENTEC low-loss Si3N4 photonic integrated optical path reflection cavity has been reported in Laser and Photonics Reviews by a team from Finland."Photonic integrated optical paths manufactured using silicon nitride waveguide platforms exhibit low loss...
2023-05-0418210ProPhotonix Limited has launched its new digital compact laser. With a diameter of just 8mm, the laser provides digital control and monitoring in an extremely compact package, ideal for space-constrained applications.Digital capabilities enable system designers to deliver higher performance products to their customers. The new high-performance la...
2023-05-0418510Star guide laser is the key technology of future space monitoring/tracking system and high performance and reliable optical communication applications. Atmospheric turbulence blurs images of celestial bodies and distorts optical communication beams. The guide laser compensates for this atmospheric turbulence.The GSTP de-risking campaign by TOPTIC...
2023-05-0424110Laser reduced graphene oxide (GO) using direct writing technology has the advantages of being highly flexible, mask free and chemical-free, promising the development of miniaturized energy storage devices. However, laser reduction of GO is usually accompanied by demineralization (a violent deoxidation reaction), resulting in the reduced graphene ox...
2023-05-0429610Hey guys… so everything I’ve tried so far has a burr I can feel with my fingernail.I found the following info on another forum but I admit I don’t understand it all since I’m still super new to laser engraving.1. do you think this would work2. how do I use the offset feature in lightburn to accomplish this?...
2023-05-0426510I just got the xtools d1 pro 40w kit and I can’t figure out good offset settings for the laser offset. It seems like no matter what I set it to it’s off, and isn’t consistent. The default setting is x-16mm,y0, but it should be something like x0mm,y-26mm. I set it to that, but it’s still offsetting something around x-10. I&rs...
2023-05-049710When I hit “home” the laser moves all the way left then up to the upper most corner and when it gets to the top it still wants to go further and the belts keep turning for about 5 seconds. I’m afraid this will damage the motors or belts. I don’t know if this is a software or hardware issue.
2023-05-0416010Hi - I just upgraded to 1.4 and I’m have some problems - I can fire the laser (2%) set the Origin and Frame the laser fires and frames ok - I then try and engrave (3mm Laserply) and the job starts the laser fires on and off (trying to engrave text) but it does not mark the wood - I have tried various speed/power settings without success - I a...
2023-05-0413610When you first install L/B a window would open and look for the laser, I just installed L/B to a new dedicated pc but this window does not pop up and in either of the settings box’s I cannot find it.
2023-05-0419410With latest version of LightBurn, undo action when using node editing is not working always.Steps to reproduce:create new filedraw some primitive shape, e.g. rectangleconvert shape to pathgo to node edit and move any point, click undo (in most cases first undo action is working)move again any other point and click undo - now undo is not workingIf...
2023-05-0424310
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski