Reasons for laser weld indentation problemDuring the laser welding process, the welding area is subjected to high temperatures, which can cause deformation due to thermal expansion and contraction, resulting in a concave weld seam. In addition, the selection of welding materials and welding parameters can also affect the occurrence of weld indentat...
2024-12-1215510Reasons for the appearance of color in laser welding seamsDuring laser welding, if the welding parameters are not appropriate, it often leads to the appearance of color in the weld seam. This problem mainly occurs on high reflective materials such as stainless steel, aluminum alloys, and titanium alloys. After analysis, in addition to inappropriate...
2024-12-1113800I’ve had my laser for A. Bout. And the horizontal lines are starting to bump or drag. I have to keep this fresh and people’s minds because.
2024-12-1011010When choosing a laser cleaning machine, to ensure the selection of suitable equipment, users need to pay attention to and confirm the following key parameters:1、 Laser powerLaser power is an important factor affecting the cleaning effect and speed. Generally speaking, the higher the power, the better the cleaning effect and the faster the speed. ...
2024-12-1023800Handheld laser welding machines, as an important tool in modern welding technology, have been widely used in various industries due to their high efficiency, precision, and flexibility. However, correct operating techniques and safety precautions are key to ensuring welding quality and operator safety. This article will provide a detailed introduct...
2024-12-0913000Recently, when I try to engrave using my Xtool D1 pro, the engraving is way off. When I frame the job, everything looks fine. But once I start to engrave, the laser moves roughly 1.5 inches to the left. This has happened consistently over the last month. I’ve managed the engraving by manually adjusting the starting point of the laser.Today, I trie...
2024-12-0698201、 Motor burnt outOne of the common faults of brushless DC motors is motor burnout. Possible reasons include overvoltage, overload, overheating, etc. If the motor is found to be burnt out, it is necessary to replace the motor and check whether the relevant circuits are working properly.2、 Controller malfunctionThe controller is a very important c...
2024-12-0714210The laser stops firing in the meddle of the job but the head doesn’t stops. When that happens, the head eventually stops, moves back and tries to keep engraving where it stops. The problem with that is that when that happens it never restart in the same position, making a really noticeable line along the path. That line is just shifted from the “or...
2024-12-0714810Introduction to Laser CladdingLaser cladding is a process of partially melting the surface of a material by irradiating it with a laser beam, spraying powder or wire onto the melted surface to generate a new surface layer. It can be used to repair damaged components, improve surface hardness, enhance surface performance, etc.Factors affecting the...
2024-12-0611700Hello,I also have the problem that when transferring data I get the error message that an error occurred while sending (the device may be busy or stopped).In the forum I found a post that you can try to set "enable DTR signal" in the device settings.Where exactly can I select this in the device settings?
2024-12-05103101、 Poor lubricationPoor lubrication is one of the main reasons for gear pitting corrosion. When the viscosity of the lubricating oil is insufficient or the pressure resistance is poor, it will weaken the lubrication and cause pitting corrosion on the friction surface. In addition, excessive impurities in lubricating oil can also affect the lubricat...
2024-12-0511200Fault performanceWhen the chiller of the laser cutting machine malfunctions, the following symptoms may occur:1. The chiller cannot start or stop. This may be caused by power failure, motor failure, water pump failure, and other reasons.2. The chiller produces excessive noise during operation. This may be caused by water pump failure, fan failure, ...
2024-12-0416610Power failure1. Check if the power cord is securely plugged in;2. Check if the power cord is damaged;3. Check if the power supply is working properly.Laser malfunction1. Check if the laser is working properly;2. Check if the laser cable is securely plugged in;3. Check if the laser cable is damaged.Other reasons1. Check if the light tube has expi...
2024-12-0410000Multiple methods can be used to avoid the problem of laser welding undercutting, such as optimizing process parameters, reducing welding speed, optimizing plate edges, etc.Reasons for laser welding edge biting problemThe problem of laser welding undercutting refers to the phenomenon of excessive melting and compression at the welding point during ...
2024-12-0213020Problem OverviewThe inability of laser cladding powder to hang refers to the phenomenon where the powder cannot uniformly adhere to the substrate during the laser scanning process, resulting in phenomena such as powder falling off. This phenomenon not only affects the processing effect, but may also damage the equipment.Root cause analysis of the...
2024-12-0316410
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski