1. Fault phenomenon one: The laser marking machine does not produce laser lightThe troubleshooting steps are as follows:Power supply inspection: Firstly, it is necessary to confirm whether the power supply wiring of the laser is correct, including whether+24V and GND are reversed, and whether the ground wire is properly grounded. Test whether the...

Terrelle

01-09

109

1

2

1、 Waterway inspectionThe main reason for abnormal water flow in the laser is due to water blockage or pump failure. Therefore, we first need to check whether the water path of the laser is blocked and whether it is well connected. If there is a blockage in the waterway, it is necessary to clean or replace the local water pipe and exhaust it. If th...

Keegan

01-06

95

0

1

Hello,we are encountering an issue with our F1 Ultra in combination with Lightburn.We recently updated everything to the newest version (XCS 2.3.24 / Lightburn 1.7.04 / F1 Ultra 40.52.012.2020.01.ht5 / Plugin 1.4.22)Today, we experienced a phenomenon where the laser suddenly shifted 1 cm to the left in the middle of the engraving. It then continued...

Erdogan

2024-12-31

213

2

0

Reasons for Laser Weakening in Laser Marking MachinesThere may be various reasons for the weakening of laser marking machine, and the following are some common reasons:1. Lens damage: If the lens is scratched, overheated, or contaminated, it can cause poor reflection and weaken the laser marking machine.2. Laser tube aging: The lifespan of laser tu...

Christian

2024-12-21

102

1

0

What is the reason for the jumping of the laser marking machine?Many people encounter jumping problems when using laser marking machines, which may be caused by the following factors:1. Machine malfunction: Long term non-stop operation of the laser marking machine during use can cause the equipment to overheat, thereby affecting its working effic...

Payson

2024-12-17

127

0

1

Power failure1. Check if the power cord is securely plugged in;2. Check if the power cord is damaged;3. Check if the power supply is working properly.Laser malfunction1. Check if the laser is working properly;2. Check if the laser cable is securely plugged in;3. Check if the laser cable is damaged.Other reasons1. Check if the light tube has expi...

Clarence

2024-12-04

64

0

0

Glass is a material with high hardness, and traditional mechanical carving methods are often difficult to use. However, as a high-precision and high-efficiency burning method, laser can overcome this difficulty. Laser engraving of glass can not only achieve high-precision engraving effects, but also preserve the properties and quality of the glass ...

jessie

2024-11-26

107

1

0

UV laser marking machine is a high-precision and high-speed laser marking equipment widely used for surface marking of various metal and non-metal materials. However, in practical use, there may be a problem of decreased laser power. This article will analyze the reasons for the power drop of ultraviolet laser marking machines and propose correspon...

Vasili

2024-11-25

92

1

0

On my rotary setup all my laser engravings work properly except for any circular shapes when done in the “line” setting.“Fill” setting works just fine as you can see in the picture with the logo.When i do shapes like an square (10x10cm) it also works just fine.Any suggestions?thanks in advance.

JOST

2024-11-19

151

4

0

Choosing a suitable laser marking machine usually involves considering multiple factors, including the type of material to be marked, the requirements for marking effect, production environment, and operational needs.Here are some considerations:Material type: Different laser marking machines are suitable for different types of materials. For exa...

Clarence

2024-11-23

117

1

0

Hi everyone - I’m a newbie to the engraving world and got everything up & running with my Creality Falcon 22W laser + Rotary Pro. I’ve watched all the YouTube videos for full wrap tumblers, messed with all the settings and after trying different things for hours and scouring the internet for my specific issue… I’m still at a loss.The laser is ...

berainlb

2024-11-04

120

3

0

Hello,We have a Boss LS 1630 and we are using the Piburn rotary attachment to try and engrave dog bowls. I have been able to use the roller to engrave cups just fine but I have tried to use the chuck for the dog bowls which are much wider in diameter. Rotary mode is turned on, steps are set, and the proper diameter and circumference of the object a...

Hiroko

2024-10-30

93

1

0

Hi,I have an issue ever since I bought the Laser master 3 engraver. I cant manage to get the lines straight, the lightburn printing test doesnt even manage to engrave normal squares and I don’t know what to do in order to resolve the problem.

AL.TAL

2024-10-21

122

1

0

My problem seems to have started after I used the rotary tool. After doing some engraving on a glass I switch to another project cutting and engraving. I discovered that my y and x axes were not accurate, so I calibrated the X axis, which went fine but I never could properly calibrate the Y axis. I read that it may be because I had to close down al...

Carey

2024-10-15

98

4

0

So when I engrave or cut the laser moves to the same position it starts from. When I use the rotary and engrave tumblers the laser head goes to a differant position from where it starts. This has changed since I upgraded from 1.6 to 1.7.01. How do I change so laser head parks after engraving in the same position it starts?

Noah

2024-10-11

129

3

0