Laser issue1. The laser is not turned onIf the laser is not turned on or does not emit a laser beam after being turned on, it may be due to the power cord not being properly plugged in or an internal problem with the laser. You can check the connection of the power cord and contact after-sales personnel for maintenance to ensure that the laser is w...
02-255000If you at the TWhat causes the arrow tips in the corners of the T all other fonts have it also except the OThis an Arial font which has been switched from a Sans Sherif font which did the same thing.From what I can see I have nothing extra switched onThe strange thing is if I increase the power the arrows go away which doesn’t work in this case. Th...
02-176661When I finished recording the topic, the measurement values in millimeters did not match.For example, I entered a value and assumed it was 5mm x 5mm and carved as 8mm x 8mm. I don't know how to fix the code so that the measured value I entered is exactly the same as the value I want to cut or carve. I appreciate any help you have provided.
01-17202301. Choose high-quality optical componentsImportance: The accuracy and durability of optical components directly affect the transmission and focusing effect of laser beams.Measures: Select optical components with high precision, low loss, and good stability, such as lenses, mirrors, etc. These components should be able to maintain long-term stable p...
02-215600Is my Ortur Laser Master 2 Pro XY out of calibration? Is there a way to calibrate mechanically or thru Lightburn SW? It is a fairly new system and not used to much. Circles and repeatability after a pause likely in the Y axis is off.
02-148050I have a longer Ray5 10watt, first laser and have had about 5 mths now. I upgraded to a enclosure, limit switches, air pump and camera. Everything is mostly good except the 5 mp camera from longer. It’s from longer and is set at the correct height. The average offset is around 1 1/2mm to 2 1/2mm depend on where it’s at on the work are. Over all it ...
02-187530Fault in the fiber optic section1. Fiber breakage: Fiber breakage is the most common situation in fiber laser machine failures, usually occurring in fibers that have been in use for a long time or have been excessively bent. The solution is to replace the fiber with a new one.2. Fiber optic pollution: When the surface of the fiber optic cable is co...
02-205100I’m trying to engrave the base of multiple trays at once.Since the sides of the trays are higher than the laser’s focus distance, the laser head bumps into them when moving from one tray (or group of trays) to another.I figured that I could use multiple layers and insert a dummy layer in between to reset the laser head to a safe height.Is there a ...
02-136960Hello! I’m new to the world of laser engraving and cutting, I have a Sculpfun S9 laser, I use Illustrator for my designs, I was making some keychains but when the shape is very complex the vector imports so badly, it gets deformed. I noticed that it does this if the vector had a lot of points, I tried to clean it up but now I see that some shapes a...
02-196010Laser cladding generally uses materials such as iron-based alloys, nickel based alloys, titanium alloys, Al Si alloys, stainless steel, etc.The materials for laser cladding are mainly metallic materials, including iron-based alloys, nickel based alloys, titanium alloys, Al Si alloys, stainless steel, and so on. These materials have good melting p...
02-196600Everything works great except lightburn is not tracking, in the program, my laser’s movement. The laser is burning, it works fine. But as you can see on the attached image, the upper green and red squares? Those never move.Any advice is appreciated, I searched but didn’t find anything that helped, maybe just a link in the right direction? Appreciat...
02-157240Principle of adjusting laser powerThe power of the laser marking machine directly determines the depth and speed of marking. Different materials have different requirements for laser power, and adjusting the laser power to be just right can ensure the best marking effect.Choose the appropriate power size1. Metal materials:For metal materials, hig...
02-157600Reasons for poor laser weldingPoor laser welding can be caused by various reasons, such as improper welding parameter settings, poor quality of welding materials, improper preparation of welding surfaces, and malfunction of welding equipment.1. Improper setting of welding parametersWhen the parameters such as laser power, focal length, and focal ...
02-145600Cuts/Layers.When I slect “fill” it does not fill the text or object in the work area? What am I missing?
02-127320Switched from rollers to chuck and now the image/texts are reversed. Did I miss a setting somewhere. Are they different from using the rollers to the chuck? Xtool D1 Pro 20W with RA2 Rotary. Any advice appreciated.
02-108840
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski