I can’t find the file send button after I upgraded to 1.4.04

Christian

2023-12-07

171

1

0

Hola tengo una sculpfun s30 ultra y el tema es queal momento de poner mi maquina en inicio no responde si le doy a ir a origen choca con los ejes y se escucha horrible y cuando pongo un trabajo lo toma como si fueran pulgadas y lo tengo en milimetros no se que hacer no me resulve soporte de ligthburn y no se que hacer

Nugent

2023-12-07

201

1

0

I’m wanting to reset my Falcon 2 to factory default. I am getting the following error: G-code motion target exceeds machine travel. Worked before playing with rotary. Would like to default Laser and Lightburn software.

Payson

2023-12-06

195

1

0

I just updated Lightburn and now my speeds and power setting dont function like they did. before 200 speed at 85% would cut 3mm. Now even 17 at 90 will not cut in one pass. Any Ideas why?Sculpfun S30. 10 W laser.

Terrelle

2023-12-06

186

1

0

After the update my position cross no longer comes on and when I frame something the laser will fire and it looks like it is in the correct place but when I run the file it is way off. Help?

Clarence

2023-12-06

194

1

0

Hi all , I have just installed the latest update 1.4.04 now when I save my work I get this pop up, not sure what is causing this any suggestions ?

Cyril

2023-12-05

196

1

0

I bought my 80w co2 laser last summer. Being nieve i didnt use any antifreeze and the tube cracked in December. I live in the Uk and my laser is in the garage. This year i bought coolflow Dtx which is designed for this purpose. Its a special antifreeze. I use the laser most days and until today it was great.The outside temperature has dropped and a...

Darren

2023-12-05

177

1

0

I am running Lighburn 1.3.01.It was connected to Fox Alien Reizer 5W laser engraver and it worked good.I have it in box in storage.I just installed a new Creality Falcon 2 and did the device setting, but it is not connecting (waiting for connection).The usb cable is good.Tried powering on and off.

Miller

2023-12-05

178

1

0

I have been engraving some stars for christmas, but after a while i encountered a problem… Whenever i want to start engraving, i get an error message“Transfer failed - Lightburn 1.4.03There was a problem sending data to the laser. The machine may be busy or paused.”Ive encountered this twice now, but on the first try i just switc...

Williams

2023-12-04

198

1

0

I have tried everything I imported an HEIF file and when I go to engrave it I get ni layers in your projecr to output, What do I need to do. I have tried all the recommenced options.

Abel

2023-12-04

202

1

0

I have been trying to make multiple passes to cut through the material however my circles do not line up.

Aaron

2023-12-04

191

1

0

How do I turn on laser beam at low power so I can set the laser on the spot where I want it to start cuting?

Marshall

2023-12-01

208

1

0

I upgrade my machine to use a more power laser a few months ago. In the past few days the power supply will begin flash and the machine will not function.I figure there is either a short with the 4 to 3 wire adapter or the laser is pulling too much power.Once I unplug the adapter to the laser the machine powers on. I assume if it was a power draw i...

Tory

2023-12-01

204

1

0

In order to swiftly heat the material to the vaporization temperature, evaporate it, and produce holes in it, laser cutting involves the employment of a high-power density laser beam. The material is cut to completion as the beam shifts it through the perforations, which continuously generate thin (like 0.1 mm) slices.The technologies involved in ...

David

2023-11-30

225

1

0

The main parameters of industrial cameras include resolution, frame rate, signal-to-noise ratio, pixel depth, etc. In addition, other important parameters also include dynamic range.Dynamic range refers to the brightness range in the scene or the photosensitive range of photosensitive materials such as film, CCD, CMOS, etc. For film and pho...

Tim Johnson

2023-11-30

185

1

0