1、 LaserLaser is the core component of laser marking machine and an important component for generating laser. Normally, the service life is long, but regular cleaning and maintenance are required. If the laser shakes or becomes unstable during use, it needs to be replaced or repaired in a timely manner.2、 LensThe lenses of a laser marking machine ...

Vasili

03-18

25

0

0

Laser marking has certain requirements for the glossiness, thickness, and hardness of aluminum material surfaces.Requirements for laser marking on aluminum material surfaceDuring the laser marking process, factors such as glossiness, thickness, and hardness of the aluminum surface can all affect the marking results. Therefore, in order to achieve...

Miller

03-04

53

0

0

I have an Algolaser DIY 20W and everything works normally. Recently, I bought a Delta 22W, and when performing the material test, I have this misalignment problem.I have already tried tightening the belts and checking for vibrations, but nothing, absolutely nothing works.Does anyone have any ideas on how to solve this?

Ruddy

02-20

86

8

0

I have a six month old sculpfun S30 22W. I have always used a kerf of 0.13mm outward when making boxes. Lately I have noticed that the joints are no longer as tight as they were at the beginning and I have to set the kerf to 0.20mm outward. Is this normal? Is there some setting somewhere, or has the beam gone out of focus?

Jack Wilborn

02-28

103

3

0

Text misaligned using rotary roller

Hiroko

02-21

58

6

0

1. If the motor burns out, generally not both machines will burn out. Just change the motor object that drives the output to test whether the other machine is normal. Motor damage can generally only be replaced by contacting after-sales service.2. Drive failure. If the drive light does not light up or flashes continuously with a burnt smell while...

Abel

02-28

53

0

0

The operating environment of laser marking machineThe laser marking machine must ensure a relatively clean surrounding environment during the production process, free from any interference from dust, grease, and chemical pollutants, which can accelerate the aging and damage of the laser marking machine.The impact of environmental dust on laser ma...

Gilbert

02-27

45

0

0

If you at the TWhat causes the arrow tips in the corners of the T all other fonts have it also except the OThis an Arial font which has been switched from a Sans Sherif font which did the same thing.From what I can see I have nothing extra switched onThe strange thing is if I increase the power the arrows go away which doesn’t work in this case. Th...

이야기 너와

02-17

64

6

1

Fault in the fiber optic section1. Fiber breakage: Fiber breakage is the most common situation in fiber laser machine failures, usually occurring in fibers that have been in use for a long time or have been excessively bent. The solution is to replace the fiber with a new one.2. Fiber optic pollution: When the surface of the fiber optic cable is co...

Smith

02-20

50

0

0

Principle of adjusting laser powerThe power of the laser marking machine directly determines the depth and speed of marking. Different materials have different requirements for laser power, and adjusting the laser power to be just right can ensure the best marking effect.Choose the appropriate power size1. Metal materials:For metal materials, hig...

Jamie

02-15

75

0

0

1. When the vertical light is incorrect, adjust the vertical light and if necessary, readjust the light path. 2. If the focal length is not adjusted properly, please refocus.3. Voltage instability, low voltage, and low laser current. You need to replace the voltage regulator with a larger one and increase the laser current output.4. If the lig...

Vasili

01-22

222

1

0

To achieve deep marking, we can adjust the parameters of the laser marking machine through the following methods:1. Adjust the focal lengthReduce the focal length to the minimum to ensure that the laser beam can be accurately focused on the surface of the material, thereby achieving the goal of deep marking.2. Adjust the laser powerLaser power i...

Liam

01-22

99

0

0

Reasons for inaccurate rotation axis1. During the use of the machine, the accuracy of the rotating shaft may decrease due to wear and tear or maintenance requirements;2. Poor manufacturing quality of the rotating shaft itself may also lead to inaccurate issues;3. During the operation of the laser engraving machine, improper control of processing sp...

Gilbert

01-21

93

0

0

In the daily operation of laser equipment, the constant emission of light is a common and difficult problem to solve. It not only affects the quality of the product, but may also increase the maintenance cost of the equipment. Faced with the problem of continuous light emission, it is urgent to quickly and accurately diagnose the location of the fa...

Abel

01-10

133

3

3

The occurrence of ghosting or blurriness during engraving operations on laser marking machines may be due to various reasons. To solve this problem, it is usually necessary to follow the following steps to check and adjust:1. Check the optical system:Confirm whether the laser and its optical components (such as lenses) are clean, as dust and stai...

Miller

2024-12-27

117

1

3