I have an Atomstack A70 with a movable z axis, the issue is that when I home the machine the z axis does not move up. I can move it with the move buttons and with a z home macro $HZ. The x and y axis home as they should. Thanks.

55455rml

2024-11-08

102

5

0

Just curious how the folks here have found using certain places on the X/Y table for placement of the work material ?I noticed, and makes sense, alot of folks use the back left corner to set up a square for dropping in material or maybe a work jig to engrave or cut.This makes sense as this is the best point for the mirror distant and it should fol...

Silvano

2024-11-11

84

3

0

I discovered after scanning some letters that the “insides” of some letters (think the “bowls” in capital B) were separate from the “outside” of the letters. I know I can Group the two objects (inside and outside) but the grouping can easily (for me) be undone accidentally. It appears that the only way of permanently joining them is to Weld them. H...

Narrator

2024-11-13

105

1

0

Hi all, I’ve been running Lightburn on an Ortur LM3 for about a month now, and a new issue has developed.I’m running a batch of bookmarks with this program, and it starts up fine, frames my object in workspace center, and runs the program in workspace center. But then…IF I PRESS START AGAIN: It repeats the program, but about 30mm to the left.IF I F...

berainlb

2024-11-13

119

1

0

Ruida 6432g will it allow a rotary hooked up to the u axis I have been trying to use the Y acess hooked to my 3 jaw rotary but it doesn't seem to let lightburn to change steps  can someone that really knows help me 

A679218C

2024-11-14

134

1

0

So I have a Creality Ender 3 S1 Plus with 5W laser module set up. It has not been cutting at its full power, because it cut the same material at the same speeds in Creality Print. So I found out that the S-Value Max setting needs to be set to your machine. My problem is I don’t know what setting to set it to. I’m including a picture of my machine s...

James

2024-11-12

135

1

0

Good morningi have a co2 laser with 6445g controlleri am engraving on granite. i have a problem with horizontally banded lines on engravingis there an upgrade of 6445g. if ibuy new like 6445gt will it be solved the problem?had anyone the same problem? please help!

029EE9D7

2024-11-11

156

1

1

Last night i was running my CO2 laser engraver and everything was running fine. Came out this morning powered on the engraver and the intial start up the head move just fine. Tried to relocate the head of the laser on the ruida controller and nothing moves.  I can't get the head to to move in either direction and the bed will not move. Light 14 is ...

36FC0F44

2024-11-11

125

3

0

I purchased a new laser and computer and downloaded light burn onto the new computer…which is an updated version compared to what I have been using. I check all my settings to make sure they match my other computers/lasers as the new laser is the same as another one I use. When I go to use it, it frames fine but when I try to engrave the laser head...

Roderick

2024-11-11

144

1

0

Dear technical departmentI recently purchased 2 units of the RDC6445S controller to install on two laser cutting machinesand I have some questions to ask.1 - What is the function of the IN1 input of the CN2 connector?2 - Where can I find updated firmware for my controller?3 - The RTlink port is a standard RS232 (+12v/-12V) or TTL port?4 - I...

Ferreira 64

2024-11-11

173

2

0

Na het instaleren van de limitswitches wat ook de nodige problemen gaf eindelijk alles good 0 postie wordt gevonden. framen laser aan met framen. eerder kreeg een continu straal die rond het werkstuk ging en de frame aangaf van af nu knippert hij, daarnaast graveert hij dus ook niet meer snijden gaat wel goed wie weet raad

이야기 너와

2024-11-09

85

1

0

All about remembering z height.when starting a cut.I’ve set my origin and home fine on the machine itself and with tests and using luban I am able to move from origin to home and back lazer something and repeat.However when using lightburn the first item placed does ok, it seems to remember the origin and home points from the machine, but for any...

Andre J

2024-11-07

106

2

0

Hi. I am attempting to use a workflow that generates the following svg i need to import into lightburn. When I import it, the font reverts to Ariel. If I ungroup everything, I can change the font but that is a big time waste. I could also export as paths, but I would prefer to maintain the ability to edit the text. Is there a way to address this? T...

Jack Wilborn

2024-11-07

139

2

0

Hi, can you please advise. Is there any way to ensure that the beginning (3-5 mm) is also cut through when cutting the poplar plywood? I can increase the power or decrease the speed, but then the rest will be pretty burnt. A ramp like a cnc milling machine would be good. Thanks.

Farouk

2024-11-06

103

3

0

Machine: Raycus 30w Fiber laserComputer: WindowsMy Raycus fiber laser stopped working. Actually, I do not think it ever worked correctly. I was never able to engrave metal with it.I have been using it to engrave water bottles for a few months. I noticed that the engraving was getting lighter (not removing all the paint) after an hour or so of use...

Andrej

2024-11-08

89

1

0