Glass is a material with high hardness, and traditional mechanical carving methods are often difficult to use. However, as a high-precision and high-efficiency burning method, laser can overcome this difficulty. Laser engraving of glass can not only achieve high-precision engraving effects, but also preserve the properties and quality of the glass ...

jessie

2024-11-26

109

1

0

In cold seasons or low-temperature environments, industrial chillers may face the risk of freezing damage, so it is very important to take effective anti freezing measures. Here are some common antifreeze strategies:1. Using antifreeze: Adding antifreeze to the cooling system is the most common method of antifreeze. Antifreeze is usually made by ...

Patrick

2024-11-26

103

0

0

let’s say I have 2 parallel curves that are close to each other… I would like to select the nodes of one of the 2 curves without also taking the nodes of the other.how do I do it?if I box the nodes I also intercept the nodes of the other curve and I haven’t found a button to select or exclude individual nodes so as to form a group that I can move a...

Durell

2024-11-18

91

6

0

UV laser marking machine is a high-precision and high-speed laser marking equipment widely used for surface marking of various metal and non-metal materials. However, in practical use, there may be a problem of decreased laser power. This article will analyze the reasons for the power drop of ultraviolet laser marking machines and propose correspon...

Vasili

2024-11-25

96

1

0

1. Autotransformer starting method: The starting voltage of the motor is reduced through an autotransformer. During the starting process, the motor is first connected to the lower voltage side of the autotransformer, and then the voltage is gradually increased to gradually accelerate the motor. After the motor reaches its rated speed, connect it to...

Payson

2024-11-25

104

0

0

On my rotary setup all my laser engravings work properly except for any circular shapes when done in the “line” setting.“Fill” setting works just fine as you can see in the picture with the logo.When i do shapes like an square (10x10cm) it also works just fine.Any suggestions?thanks in advance.

JOST

2024-11-19

152

4

0

Choosing a suitable laser marking machine usually involves considering multiple factors, including the type of material to be marked, the requirements for marking effect, production environment, and operational needs.Here are some considerations:Material type: Different laser marking machines are suitable for different types of materials. For exa...

Clarence

2024-11-23

118

1

0

Hello, I am currently building a fiber laser with the following components-Ruida rdc 6563 FG controller-Z motor and driver Fuji GYB401D5-RC2-B and RYH401f5-vv2-Raytools BT210S laser head-Raycus RFL-C1500 laser source-Water cooler S&A Pro Series CWFL-1500I have problems with the cap calibration,If I am more than 10mm away from the metal th...

CD354C6F

2024-11-22

279

1

0

Vibration knife is a modern CNC cutting equipment equipped with an intelligent control system. Its principle is to quickly complete cutting and processing by vibrating the blade up and down at a very high frequency. Under the command of the control system, the vibrating knife has high precision and fast processing speed, and is widely used in non-m...

Gilbert

2024-11-23

77

0

0

after installing a 20W upgrade laser from the 10W, laser will go to orgin, frame but when homing to the proper left hand cornner it makes a huge grinding noise. I tried the manual method but still have the same results.

Noah

2024-11-20

136

2

0

Hello. I recently upgraded Lightburn to 1.7.03. I am using Xtool Pro for my work. I am struggling to figure out why the laser head goes off in the wrong direction and then stops with a beep. It’s not hitting the limiter switch.Attempting to engrave an image on acrylic. Lining up the laser on the top left corner of the work piece and it frames the ...

Cruise Wang

2024-11-19

140

3

0

I have the same problem like in this video my machine add random extra line to my output cuttingany help ? https://www.youtube.com/watch?v=5DDVqcbVISM

SMIX24

2024-11-19

145

5

0

I gave up last year on trying to figure out my Boss Laser (LS1416) and just stopped using it, however last week I decided to take one more run at it. I now have a new issue stopping me. When I plug in my PiBurn rotary tool and try to do anything, the laser head slams into the right rail and starts grinding. I believe I am running a recent version o...

Ethan

2024-11-20

129

1

0

I get very bad curves. Belts are tight. What else happens? Is this normal from the stepper motors or something i have to check?Thanks in advance

Andrej

2024-11-18

109

2

0

I am sure I am not the only one here that has this happening, most likely with every K40 machine. My machine reaches max output milliamp output at 22-23% output in Lightburn. Would it be possible to calibrate the power output so that it reaches max Milliamp output at 100% in Lightburn power settings?

Hiroko

2024-11-12

178

4

0