1、 Poor lubricationPoor lubrication is one of the main reasons for gear pitting corrosion. When the viscosity of the lubricating oil is insufficient or the pressure resistance is poor, it will weaken the lubrication and cause pitting corrosion on the friction surface. In addition, excessive impurities in lubricating oil can also affect the lubricat...
2024-12-056900Fault performanceWhen the chiller of the laser cutting machine malfunctions, the following symptoms may occur:1. The chiller cannot start or stop. This may be caused by power failure, motor failure, water pump failure, and other reasons.2. The chiller produces excessive noise during operation. This may be caused by water pump failure, fan failure, ...
2024-12-0413110Power failure1. Check if the power cord is securely plugged in;2. Check if the power cord is damaged;3. Check if the power supply is working properly.Laser malfunction1. Check if the laser is working properly;2. Check if the laser cable is securely plugged in;3. Check if the laser cable is damaged.Other reasons1. Check if the light tube has expi...
2024-12-046800Multiple methods can be used to avoid the problem of laser welding undercutting, such as optimizing process parameters, reducing welding speed, optimizing plate edges, etc.Reasons for laser welding edge biting problemThe problem of laser welding undercutting refers to the phenomenon of excessive melting and compression at the welding point during ...
2024-12-029120Problem OverviewThe inability of laser cladding powder to hang refers to the phenomenon where the powder cannot uniformly adhere to the substrate during the laser scanning process, resulting in phenomena such as powder falling off. This phenomenon not only affects the processing effect, but may also damage the equipment.Root cause analysis of the...
2024-12-0311910Parameter adjustment skillsIt is very important to set and adjust parameters correctly when performing handheld laser welding. Here are some parameter adjustment techniques:1. PowerHandheld laser welding machines are usually equipped with adjustable focal lengths. During the welding process, the focal length can be adjusted according to the condi...
2024-12-039100With the rapid development of laser cleaning technology, it has gradually entered people's lives due to its unique advantages such as low damage to the substrate material, high cleaning accuracy, zero emissions, and no pollution. There is no doubt that applying laser cleaning technology to the cleaning of dirt on metal surfaces has a very broad pro...
2024-11-2910421UV laser is a special type of laser with a short wavelength, concentrated energy, and short pulse frequency. The wavelength range of this laser is between 200~400nm, and its high-energy photons can break chemical bonds on materials at the molecular level, thereby achieving the effect of separating and breaking materials. These characteristics make ...
2024-12-0297001. Self melting alloy powdercharacteristic:Containing B and Si (functions: deoxidation, slagging).Substrate adaptability.It can be widely used in various materials including carbon steel, alloy steel, stainless steel, and cast iron, but it is not suitable for steel with high sulfur content because the sulfur in the steel will form a low melting poi...
2024-11-299400Reasons for unstable power of synchronous motors1. Poor circuit connection: The circuit connection of synchronous motors, such as poor circuit connection and poor contact of contacts, can lead to unstable motor power.2. Mechanical load changes: The operating environment and load changes of synchronous motors can affect the output power of the moto...
2024-11-2810010Vibration knife is a modern new type of CNC cutting method, named after its blade that vibrates up and down at extremely high frequencies to complete cutting. The vibration knife equipment is equipped with an intelligent CNC system. With the help of the CNC system, the vibration knife can accurately and quickly complete various machining tasks, and...
2024-11-2813600I have an S1 and am currently using Lightburn 7.03. In previous forums, there was lengthy discussions about this issue and last May, it was posted that the new Lightburn version 7.0 would fix it. I cam using the current version, and my S1 is still cutting triangles when I put a square around a design to be cut. It finishes cutting the design and th...
2024-11-2113550To improve the efficiency and stability of laser welding, the following aspects can be considered and operated:1、 Equipment selection and optimizationChoosing high-power lasers: Higher power output can significantly accelerate welding speed, thereby improving overall efficiency.Equipped with advanced optical systems: can effectively ensure beam qu...
2024-11-279310Gears and racks, as common transmission components in mechanical equipment, their maintenance is crucial for ensuring stable operation and extending the service life of the equipment. The following are key points to note when performing gear and rack maintenance:Maintaining cleanliness and proper lubrication are crucial. Regularly remove dirt and...
2024-11-277400Offset - Lightburn 1.7.03The operation is different for 1 mm or 0.15mm, the generated images are not independent.The external direction generates 2 shapesThe inner direction does not generate anythingThe direction Both generate 2 shapes that are not independent for small values 0.15mm.
2024-11-2112240
- No Data
English
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski