On my rotary setup all my laser engravings work properly except for any circular shapes when done in the “line” setting.“Fill” setting works just fine as you can see in the picture with the logo.When i do shapes like an square (10x10cm) it also works just fine.Any suggestions?thanks in advance.

JOST

2024-11-19

157

4

0

Choosing a suitable laser marking machine usually involves considering multiple factors, including the type of material to be marked, the requirements for marking effect, production environment, and operational needs.Here are some considerations:Material type: Different laser marking machines are suitable for different types of materials. For exa...

Clarence

2024-11-23

123

1

0

Hello, I am currently building a fiber laser with the following components-Ruida rdc 6563 FG controller-Z motor and driver Fuji GYB401D5-RC2-B and RYH401f5-vv2-Raytools BT210S laser head-Raycus RFL-C1500 laser source-Water cooler S&A Pro Series CWFL-1500I have problems with the cap calibration,If I am more than 10mm away from the metal th...

CD354C6F

2024-11-22

292

1

0

Vibration knife is a modern CNC cutting equipment equipped with an intelligent control system. Its principle is to quickly complete cutting and processing by vibrating the blade up and down at a very high frequency. Under the command of the control system, the vibrating knife has high precision and fast processing speed, and is widely used in non-m...

Gilbert

2024-11-23

81

0

0

after installing a 20W upgrade laser from the 10W, laser will go to orgin, frame but when homing to the proper left hand cornner it makes a huge grinding noise. I tried the manual method but still have the same results.

Noah

2024-11-20

139

2

0

Hello. I recently upgraded Lightburn to 1.7.03. I am using Xtool Pro for my work. I am struggling to figure out why the laser head goes off in the wrong direction and then stops with a beep. It’s not hitting the limiter switch.Attempting to engrave an image on acrylic. Lining up the laser on the top left corner of the work piece and it frames the ...

Cruise Wang

2024-11-19

142

3

0

I have the same problem like in this video my machine add random extra line to my output cuttingany help ? https://www.youtube.com/watch?v=5DDVqcbVISM

SMIX24

2024-11-19

151

5

0

I gave up last year on trying to figure out my Boss Laser (LS1416) and just stopped using it, however last week I decided to take one more run at it. I now have a new issue stopping me. When I plug in my PiBurn rotary tool and try to do anything, the laser head slams into the right rail and starts grinding. I believe I am running a recent version o...

Ethan

2024-11-20

133

1

0

I get very bad curves. Belts are tight. What else happens? Is this normal from the stepper motors or something i have to check?Thanks in advance

Andrej

2024-11-18

113

2

0

I am sure I am not the only one here that has this happening, most likely with every K40 machine. My machine reaches max output milliamp output at 22-23% output in Lightburn. Would it be possible to calibrate the power output so that it reaches max Milliamp output at 100% in Lightburn power settings?

Hiroko

2024-11-12

187

4

0

Hi forum,I’m just strting with my JTech laser on a Onfininty Elite machine and was trying some different setting yesterday on oak.What I saw is that with a offset fill I have clean edges. But with just the lines, they are serrated.Any idea how to avoid this?

Carey

2024-11-09

153

6

0

My Gweike laser was working fine, it recently started saying I have the material thickness set to or near zero. I did not even know you can set the material thickness. Anyone know why this is showing up and how to fix it? 

AL.TAL

2024-11-15

122

1

0

Any of you out there consistently cut half-inch acrylic? I did it once by trial and error and because my settings were wrong, I actually damaged my edges a little bit. I only have one piece to get one shot at this.I have access to a shared machine, which is 100 W. We have a 4 inch cutting head In which I don’t have that much experience with.Can you...

さいと康成

2024-11-15

121

2

0

it doesnt matter what i try I can draw a circle and then a square and the weld command may or may not highlight… booleon never does. it just started in current version

Erdogan

2024-11-15

117

1

0

Vibration knife is a new type of CNC cutting equipment, whose principle is that the vibration knife blade vibrates up and down at a very high frequency, and through repeated cutting in a short period of time, it can quickly complete the machining. Under the command of the control system, the vibrating knife can complete designated tasks with high a...

Darren

2024-11-15

114

0

0