I am engraving a square box-shaped ruler. The lines engrave lighter on the X-Axis than they do on the Y-Axis. They are all on the same layer with the same settings.Why does this happen and how do I fix it?

LWE

01-21

93

2

1

After a few cuts my brand new laser (Atomstack A10 pro V2 Black) suddenly did not ray (burning / firing), at the same time It is moving properly, fan works, two leds at laser module works (pwm is blue, power is orange).Such bad behavior exists both: under WIFI via Atom Stack Mobile app and USB control via LightBurn.I checked similar topics, and my ...

Hiroko

01-14

158

8

0

1. When the vertical light is incorrect, adjust the vertical light and if necessary, readjust the light path. 2. If the focal length is not adjusted properly, please refocus.3. Voltage instability, low voltage, and low laser current. You need to replace the voltage regulator with a larger one and increase the laser current output.4. If the lig...

Vasili

01-22

231

1

0

To achieve deep marking, we can adjust the parameters of the laser marking machine through the following methods:1. Adjust the focal lengthReduce the focal length to the minimum to ensure that the laser beam can be accurately focused on the surface of the material, thereby achieving the goal of deep marking.2. Adjust the laser powerLaser power i...

Liam

01-22

105

0

0

I’m trying to see my GRBL settings, but I can’t type anything into the command window.Side note: I’m new to this, and I’m only trying to see these settings to address a different issue. I have a Monport 30W fiber laser.

Tim Johnson

01-20

77

2

0

Reasons for inaccurate rotation axis1. During the use of the machine, the accuracy of the rotating shaft may decrease due to wear and tear or maintenance requirements;2. Poor manufacturing quality of the rotating shaft itself may also lead to inaccurate issues;3. During the operation of the laser engraving machine, improper control of processing sp...

Gilbert

01-21

97

0

0

I am hoping I will be able to import vector artwork from exterior programs to MillMage and I was wondering if that will be possible? I currently have Affinity Designer 2 and Inkscape- I am a graphic designer and they are easy for me to use. Or will it be better to do all the vector work in MillMage, when it comes out? Will MillMage be able to have ...

Erdogan

01-18

134

2

0

Hi All,I recently updated to v1.7.04 from very old version. I’m setting up a diode laser machine (that was working on that old version) and have upgraded the controller to an MKS SBase I had lying around), running Smoothieware.What happened to the “Laser Control Commands” in Device Settings? I’m struggling to get the laser to fire properly.It’d a...

Narrator

01-16

141

4

0

The reason for the sudden failure of laser cutting machine1. Laser malfunction. Laser is the core component of laser cutting machine. If the laser malfunctions, it will cause the laser cutting machine to malfunction.2. Optical path malfunction. The optical path is the channel through which the laser cutting machine transmits laser and performs cutt...

Vasili

01-20

75

0

1

1、 Reason for the problemIn the process of laser cutting, if the cutting line is too small or the laser power is too low, there will be a problem of non closure. In addition, if the cutting speed is too fast, this problem is also prone to occur. In addition, the material of laser cutting can also affect the closure of the cutting, and if the materi...

Christian

01-18

92

0

0

I have a image that i duplicated a few time to make a longer image. I am trying to make this image fit into a circle to make this image round.I can do text fine. But not images. If there is away, please let me know. Thanks.

RTP

01-13

105

8

0

Probably is a dumb question, but is there a simple way if stopping knives on the laser bed from falling inwards when u take honeycomb in and out. Had to replace my knives and holder. Have tried hot gluing tabs on ends where the knives seat but they fall off after a week ot so.

Ruddy

01-15

114

3

0

I have a two trees TTS20 Pro, I have it set up to home at front left as per the instructions in my lasers manual, but the machine keeps trying to home at back left and when doing so it slams into the top and side walls and makes a terrible grinding sound.All images are engraved upside down to what is shown on LightBurn.I have tried deleting my lase...

Roderick

01-10

90

5

0

pneumatic punching machine ‌manufacturerIntroduction of pneumatic punching machine‌:Pneumatic punching machine is a kind of punching equipment which uses compressed air as power source and controls the punch to move up and down through the pneumatic system.It is widely used in a variety of metal,non-metallic materials stamping processing,such as ...

DE19B85E

2024-12-31

108

5

0

In the daily operation of laser equipment, the constant emission of light is a common and difficult problem to solve. It not only affects the quality of the product, but may also increase the maintenance cost of the equipment. Faced with the problem of continuous light emission, it is urgent to quickly and accurately diagnose the location of the fa...

Abel

01-10

135

3

3