I’m trying to cut a project 3 ft long - so using the print and cut feature. After I cut my first of the three parts (i broke the project up into 1 ft incriments) I go to align my laser with the registration marks; however, after i move my laser head to the mark and choose “set first target position”, i then frame the registration mark and the laser...

RTP

2024-10-17

105

2

0

So when I engrave or cut the laser moves to the same position it starts from. When I use the rotary and engrave tumblers the laser head goes to a differant position from where it starts. This has changed since I upgraded from 1.6 to 1.7.01. How do I change so laser head parks after engraving in the same position it starts?

Noah

2024-10-11

129

3

0

I built a project and set the cuts/layers speed to 10 and saved the project. I then reselected the project and loaded to the art library. When I bring the project from the art library to the workspace the speed in cuts/layers has changed. I’m using Lightburn 1.7.01 on a windows 10 laptop.

Erdogan

2024-10-10

172

1

0

We are setting up a laser machine to carve copper; From the first test, for example, by digging a small square at 0 degrees, a Z-dip angle of approximately 10-15 degrees can be obtained. What parameters should we use for perfect straight line cutting?

55455rml

2024-10-09

94

1

0

Im new to laser cutting / engraving so please forgive my ignorance . I have been told to use a coolant for my laser cutter . Can any of u legends give some helpful advice on the coolant i should use ?

JOST

2024-10-05

99

1

0

Hi,Just bought a fiber laser and want to download a materials parameters library from The Laser Master Academy, which have been essentially useless in helping me. So I thought I would try here because of past successes.I am on a Mac with Sonoma 14.5, I am also using LightBurn 1.6.03. I initially downloaded the document and got the message that I ...

berainlb

2024-09-25

136

2

0

I am cutting out two plywood rectangles to be glued back to back using the same rectangle drawn in Lightburn but when I fit the plywood together, it does not line up square. What am I doing wrong? Thanks!

Andre J

2024-09-14

165

2

0

hello everyone! trying out 1.7rc 7one thing ive found is it wont save cut settingshave checked and load defult layer settings on new or start up is on

Ruddy

2024-09-13

118

1

0

Hi Folks,i want to cut Parts for a Modell airplane, but there is only small differences between this parts, so i have to engrave some Numbers on them.I marked this Numbers and set them to Layer 02. In cutting options i reduced the Laser Intensity so that he only engrave this parts.But how can i set Lightburn, that its doing First the engraving and ...

Terrelle

2024-09-12

137

1

0

It is generally recommended to lubricate the laser cutting machine once per hour, and the specific time can be adjusted according to the actual situation.The function of lubricating oilLaser cutting machines require the use of lubricating oil during operation to reduce friction and wear, protect various components of the machine, and extend the s...

Jen

2024-08-29

77

0

0

1. Adjust equipment parameters:According to the thickness and type of material, increase the laser power and frequency appropriately to make the laser beam act more strongly and densely on the material. Optimize the focusing system to ensure accurate focusing of the laser beam and improve cutting efficiency.2. Optimize cutting process:Reasonably ...

jessie

2024-08-07

88

0

0

In industrial production, the completed thin film materials are usually rolled into large rolls, which need to be cut into small pieces of different shapes according to the purpose. Laser cutting is one of the main processing methods for thin film cutting.Laser cutting of thin film materials has the following advantages:High precision: With the s...

Clarence

2024-08-05

101

0

1

The range of non-metallic materials is very wide, and there are various processing methods. However, in the face of high-power lasers, it is usually only necessary to consider the optical properties of the material to determine whether it can be processed by laser. Laser cutting of non-metallic materials mainly uses CO2 lasers with a wavelength of ...

Cyril

2024-08-03

116

1

0

Polarizing film is a special thin film material, also known as polarizing film. Polarizing film is an optical component that can convert light into polarized light. Its principle is to absorb light with a vibration direction perpendicular to the transmission axis of the polarizing film, so that only light with a vibration direction parallel to the ...

Smith

2024-08-02

100

1

0

Polymer materials, also known as polymer materials, are materials composed of polymer compounds as the matrix and other additives. There are many types of polymer materials, which can be divided into natural polymer materials and synthetic polymer materials. Among them, natural polymer materials include natural fibers, natural gum, animal glue, etc...

Miller

2024-08-02

103

0

0